VXI VM4016 user manual Inhouseregenable

Page 24

VXI Technology, Inc.

INHOUSE:REG_ENABLE

The INHOUSE:REG_ENABLE command controls the masking for REGINT. REG_ENABLE 0 means that backplane interrupts cannot be generated. If the REG_ENABLE is 1, then backplane interrupts can be generated. If PSEUDO is set, then a write to the register at offset 0x38 also controls the masking. Enable or disable capabilities are provided in the pseudo register interface to allow a complete register interface. It is important to note that all letters of the command must be provided as there is no short form for this command.

INHOUSE:REG_ENABLE <boolean>	Where <boolean> is 0 OFF 1 ON.

EXAMPLES
INHOUSE:REG_ENABLE 1	Enables the REGINT type interrupt
	generation
INHOUSE:REG_ENABLE?	Returns 1 to state that backplane
1	interrupting is currently enabled.
INHOUSE:REG_ENABLE 0	Disabling REGINT interrupt generation.
INHOUSE:REG_ENABLE?	Returns 0 to state that backplane
0	interrupting is currently disabled.

24	VM4016 Programming

Image 24

Contents VM4016 Page Table of Contents VXI Technology, Inc Warranty Limitation of WarrantyCertification Restricted Rights LegendC L a R a T I O N O F C O N F O R M I T Y EMCGeneral Safety Instructions Terms and SymbolsThis product. Product should be inspected or serviced Support Resources VXI Technology, Inc VM4016 Preface Introduction IntroductionDescription Front Panel LayoutVM4016 Block Diagram VM4016 General Specifications IRQ OutputInstallation Calculating System Power and Cooling RequirementsPreparation for USE Setting the Chassis Backplane Jumpers Setting the Logical AddressFront Panel Interface Wiring Signal PIN Number Analog Comparator PIN Outs1631 Examples of Scpi Commands FETCHCONDITIONED? ProgrammingFETCHLATCHED? FETCHRAW? Inhousepseudo Inhouseregint InhouseregintInhouseregenable Inhouseclearlatch Inputdebounce ExamplesInputmask INPMASK?INPutMASKINTerrupt boolean Where boolean is 0 OFF 1 on InputmaskinterruptInputoffset INPOFFS?Inputpolarity INPutPOLarity NORM,@35Inputrange Outputpolarityexternalinterrupt Outputpolarityexternallatched Application Examples ExampleCommands Description Single Channel OperationControl Page Bracketing a Voltage Sets the external interrupt output to be active highBracketing AN Input Voltage Page Register Access Examples Register MAPFor example Pseudo Register Access VXIPLUG&PLAY Driver Examples VM4016 Programming VXI Technology, Inc Command Dictionary Alphabetical Command ListingIeee 488.2 Common Commands Instrument Specific Scpi Commands NormalScpi Required Commands Command Dictionary Query ParametersCommon Scpi Commands CLSESE Response DescriptionESR? IDN? OPC Query Parameters Query Response DescriptionRST SRE STB? TRG TST? WAI OPCInstrument Specific Scpi Commands FETChCONDitioned?FETChLATChed? FETChRAW? Inhouseclearlatch Inhousepseudo Inhouseregint Inhouseregenable INPutDEBounce INPutMASK INPutMASKINTerrupt INPutOFFSet INPutPOLarity INPutRANGe OUTPutPOLarityEXTernalINTerrupt OUTPutPOLarityEXTernalLATChed Required Scpi Commands STATusOPERationCONDition?STATusOPERationENABle STATusOPERationEVENt? STATusPRESet STATusQUEStionableCONDition? STATusQUEStionableENABle STATusQUEStionableEVENt SYSTemERRor? SYSTemVERSion? Theory of Operation Input Range Control Relay Signal Comparison Interrupt Generation Interrupt Generation Index OUTPutPOLarityEXTernalLATChed