Omron BU3002SW, BU1002SW When using UPS Power Manager UPS monitoring software for Mac

Page 70

7．Using the UPS monitoring software and contact signal

* When connecting 2 or more computers to the UPS

UPS	Power cable

Power cable	LAN connection
	LAN connection
	PC server 3
Power cable	Network
	Network
	PC server 2
Power cable

PC server 1	Switching hub

Remote connection

The included connection cable (RS-232C or USB)

2. Install the included UPS monitoring software on each computers.

Software to install: PowerAct Pro

How to install: Refer to the separate “UPS monitoring software installation guide”.

●When using UPS Power Manager “UPS monitoring software for Mac”

1.Connect the UPS to a computer.

Cable: Included USB communication cable

*Only 1 computer can be connected to the UPS

2.Install the included UPS monitoring software on the computer.

Software to install: UPS Power Manager

How to install: Refer to the separate “UPS monitoring software quick installation guide”.

<USB>
Connect to
USB
terminal
Connector
	Connector
Connect to	Connect to
USB Port	USB
on UPS	Connector terminal
Connect to USB
port on PC
	Connect to USB
	port on PC

Connector

Connect to USB Port

on UPS

	Included connection cable(USB)	BU1002SW	Included connection cable(USB)
			BU3002SW

68

Image 70

Contents BU1002SW/BU3002SW Introduction Internal Battery Procedure from installation to operation Start Installation/connectionTable of Contents Keep plastic package bags out of reach of children Safety precautionsMisuse may cause death or serious injury Do not disassemble, repair, or modify the unit Provide secure groundingDo not pinch or tie the cable of the unit Doing so may compromise the safety of devices Do not allow the unit to come in contact with water If fluid leaks from the unit, do not touch the fluidUse a specified battery for replacement Do not insert metal objects into the battery connectorsPerform replacement on a stable and flat place Do not disassemble or modify the batteryDo not put the battery into fire and do not break it Do not use a new battery and an old battery at the same timeDo not perform a withstand voltage test Scheduled operation using the UPS monitoring software Quitting Battery ModeRebooting This unit uses lead acid batteriesPreparation 2Checking the contentsUnpacking the product Name of each part Front viewSide view Rear view BU1002SW BU3002SWExplanation of symbols used on unit Installation and connection Precautions and notes on installation and connectionDo not install the unit in other than specified orientations Installation and connection Do not perform a withstand voltage test Installation and connection BU1002SWBU3002SW Casters locked Connecting the equipment Group control of power supply outputConnecting a device to the power supply output BU1002SW Output on Output OFFNfpa Input plug L6-15P Front view Connecting a device to the power supply output BU3002SW BU3002SW Rated value of output capacity Max kVA/2100WRear panel Input plug L6-20P Front view Checking the operation Turn on the units power switchBring all the connected devices into operation Battery Mode, check the units LED display and beep sound OFFMeasuring the initial value of backup time Charging the batteryRecharging the battery Precautions and notes for operation OperationExplanation Start procedure Start and stop procedures and basic operationOperation Turn on the power switch of the UPS Operation after a power failure Setting switch 1 can be used to turn the beeper ON/OFF.Stop procedure Operation during recovery from a power failureConnection capacity/battery level meter Interpreting beeps and displays Displays and beeps in normal operationDisplay and beep for battery replacement Suspending a beep UPS functionsSelf-diagnosis test Description of the auto battery test function Changing the setting of the functionsSetting switch function list UPS functions BS signal reception time corresponds to the setting switch BS signal valid range setting setting switch Settings available for this operation are shown below UPS operation mode settingsSettable items and explanations OFF Settings Cold start Estimated backup time Measuring the backup timeHow to measure backup time For Windows Server 2003/XP/Me/2000/Windows NT/Linux/MacBUM100S Life of battery estimated replacement timing Maintenance and InspectionChecking the battery Methods for checking the batteryReplacing the battery Battery recycling Procedure for recycling the batteryDo not hold the connector or cable of the battery pack Tighten the 2 screws Battery replacement is now complete Red tape Tighten 2 screws After replacing the battery during operation Replacing the fan Do not put your fingers into the fanFan replacement procedure Cleaning Cleaning the UPSUsing the UPS monitoring software and contact signal UPS monitoring softwareSoftware title Connect the UPS to a computer RS-232CWhen using UPS Power Manager UPS monitoring software for Mac When connecting 2 or more computers to the UPSExplanation Install the included UPS service driver on the computer Connector Perform UPS service setup ClickRecycling and Discarding the Battery Stopping the UPSHow to set up UPS service set the time to shut down Windows Check Set ClickCheck Set Check Set Signal output Contact signalContact Signal Low battery level signal output BLItems that can be set using the contact signal card Remote ON/OFF SignalOutput delay time setting for backup signal output BU BU/BL signal reverse output settingInsert/ removal method of contact signal card Contact Signal Connector female DSUB9PContact Signal circuit inside the UPS Remote ON/OFF connectorContact Signal ratings Example of the use of the Contact Signal circuitPrecautions and notes for the use of the Contact Signal Remote ON/OFF circuitUsing an SNMP/Web card Adding an SNMP/Web cardSpecifications Description featuresSNMP/Web card outline Extending the backup time Connecting an additional battery unitAdding BUM300S to the BU3002SW Troubleshooting Problem Check and remedySpecifications ReferencesDimensions BU3002SWCircuit block diagram Related productsK1L-D-06051B