Omron BU3002SW, BU1002SW specifications References, Specifications

Page 90

Reference

References

A. Specifications

Type

 

BU1002SW

BU3002SW

Method

Operation method

Full-time inverter supply method

 

Connectable devices

PC, display, and peripherals

Input

Rated input voltage

200 to 240V ± 10%

 

Allowable voltage range

AC145±4 to 276±4V (with 85% or less connection load)

 

 

AC170±4 to 276±4V (with 85% or more connection load)

 

Frequency

50/60Hz ± 4Hz

 

Maximum current

7.4A

16A

 

Phase

Single-phase, two-wire

 

Input plug shape

NEMAL6-15P

NEMAL6-20P

 

Input protection

Reset-type overcurrent protection device

 

Input protection capacity

10A

20A

Output

Allowable connection capacity *1

1000VA/700W

3000VA/2100W

 

Voltage (effective value) *2

200V mode

AC200V ± 3%

 

 

220V mode

AC220V ± 3%

 

 

230V mode

AC230V ± 3%

 

 

240V mode

AC240V ± 3%

 

Peak voltage value

200V mode: AC282V ± 6% 220V mode: AC310V ± 6%

 

(In Commercial Power Mode)

230V modeAC324V±6% 240V modeAC338V±6%

 

Peak voltage value

200V modeAC282V±6%

220V modeAC310V+6%/-10%

 

(In Battery Mode)

230V modeAC324V+6%/-10% 240V modeAC338V+6%/-12%

 

Frequency

50/60Hz ± 1Hz

 

Phase

Single-phase, two-wire

 

Output waveform

Sine wave

 

Waveform distortion rate

200V mode: 6% max.

220V mode: 10% max.

 

(Rectified load, at rated output)

230V mode: 10% max.

240V mode: 12% max.

 

Number of output receptacles

IEC60320 C13 : 3 pcs.

IEC60320 C19 : 1 pcs. C13 : 5 pcs.

 

 

Terminal block: 2 lines

Terminal block: 2 lines

 

Power failure switching time

Uninterrupted

 

Commercial direct shipment (switching time)

4msec. max.

 

Backup time *3

Minimum 5 minutes

Battery

Type

Compact sealed lead battery

 

Sealed lead battery life expectancy

4 to 5 years (long operating life) *At ambient temperature of 20°C

 

Battery capacity (V/Ah) (x Quantity)

12V DC/ 7.2 Ah (x 3)

12V DC/ 9 Ah (x 6)

 

Charging time

8 hours *4

Environment

Operating ambient temperature

0 to 40°C (during operation)/ -15 to 50°C (during storage)

 

Operating ambient humidity

25 to 85%RH (during use)/10 to 90%RH (during storage)

Dimensions

 

145 x 395 x 224 (±1) mm *5

213 x 537 x 432 (±1) mm *6

Weight of unit

 

Approx. 15.5 kg

Approx. 35 kg

Internal power

 

50W (100W max.)

55W (155W max.) *7

consumption (max.)

 

 

 

 

Noise regulation

 

VCCI Class A

(compliance standard)

 

 

 

 

Safety standard compliance

 

UL/CE

Noise

 

50 dB max.

55 dB max.

*1: Make sure that both the VA value and the W value of the load capacity connected to the UPS are within the range specified here.

*2: Check the operation beforehand if the unit is used in any mode other than “200V AC mode”. In some cases, the maximum voltage of output in Battery Mode may be lower than the maximum voltage in usual operation (commercial power supply).

*3: The backup times shown here are for when rated load is connected, at 20°C, and for initial characteristics.

*4: When an additional battery unit is connected, the charging time is 24 hours.

*5: The height includes the 13-mm height of the rubber feet.

*6: The height includes the 56mm height of the casters.

*7: 170W max when and additional battery unit is connected.

88

Image 90
Contents BU1002SW/BU3002SW Introduction Internal Battery Procedure from installation to operation Start Installation/connectionTable of Contents Safety precautions Keep plastic package bags out of reach of childrenMisuse may cause death or serious injury Provide secure grounding Do not disassemble, repair, or modify the unitDo not pinch or tie the cable of the unit Doing so may compromise the safety of devices Do not allow the unit to come in contact with water If fluid leaks from the unit, do not touch the fluidUse a specified battery for replacement Do not insert metal objects into the battery connectorsPerform replacement on a stable and flat place Do not disassemble or modify the batteryDo not put the battery into fire and do not break it Do not use a new battery and an old battery at the same timeDo not perform a withstand voltage test Scheduled operation using the UPS monitoring software Quitting Battery ModeRebooting This unit uses lead acid batteries2Checking the contents PreparationUnpacking the product Name of each part Front viewSide view Rear view BU1002SW BU3002SWExplanation of symbols used on unit Installation and connection Precautions and notes on installation and connectionDo not install the unit in other than specified orientations Installation and connection Do not perform a withstand voltage test Installation and connection BU1002SWBU3002SW Casters locked Connecting the equipment Group control of power supply outputConnecting a device to the power supply output BU1002SW Output on Output OFFNfpa Input plug L6-15P Front view Connecting a device to the power supply output BU3002SW BU3002SW Rated value of output capacity Max kVA/2100WRear panel Input plug L6-20P Front view Turn on the units power switch Checking the operationBring all the connected devices into operation Battery Mode, check the units LED display and beep sound OFFCharging the battery Measuring the initial value of backup timeRecharging the battery Precautions and notes for operation OperationExplanation Start and stop procedures and basic operation Start procedureOperation Turn on the power switch of the UPS Operation after a power failure Setting switch 1 can be used to turn the beeper ON/OFF.Operation during recovery from a power failure Stop procedureConnection capacity/battery level meter Interpreting beeps and displays Displays and beeps in normal operationDisplay and beep for battery replacement UPS functions Suspending a beepSelf-diagnosis test Description of the auto battery test function Changing the setting of the functionsSetting switch function list UPS functions BS signal reception time corresponds to the setting switch BS signal valid range setting setting switch UPS operation mode settings Settings available for this operation are shown belowSettable items and explanations OFF Settings Cold start Estimated backup time Measuring the backup timeHow to measure backup time For Windows Server 2003/XP/Me/2000/Windows NT/Linux/MacBUM100S Life of battery estimated replacement timing Maintenance and InspectionChecking the battery Methods for checking the batteryReplacing the battery Battery recycling Procedure for recycling the batteryDo not hold the connector or cable of the battery pack Tighten the 2 screws Battery replacement is now complete Red tape Tighten 2 screws After replacing the battery during operation Replacing the fan Do not put your fingers into the fanFan replacement procedure Cleaning Cleaning the UPSUsing the UPS monitoring software and contact signal UPS monitoring softwareSoftware title Connect the UPS to a computer RS-232CWhen using UPS Power Manager UPS monitoring software for Mac When connecting 2 or more computers to the UPSExplanation Install the included UPS service driver on the computer Connector Perform UPS service setup ClickRecycling and Discarding the Battery Stopping the UPSHow to set up UPS service set the time to shut down Windows Check Set ClickCheck Set Check Set Signal output Contact signalContact Signal Low battery level signal output BLItems that can be set using the contact signal card Remote ON/OFF SignalOutput delay time setting for backup signal output BU BU/BL signal reverse output settingInsert/ removal method of contact signal card Contact Signal Connector female DSUB9PContact Signal circuit inside the UPS Remote ON/OFF connectorContact Signal ratings Example of the use of the Contact Signal circuitPrecautions and notes for the use of the Contact Signal Remote ON/OFF circuitUsing an SNMP/Web card Adding an SNMP/Web cardDescription features SpecificationsSNMP/Web card outline Extending the backup time Connecting an additional battery unitAdding BUM300S to the BU3002SW Troubleshooting Problem Check and remedySpecifications ReferencesDimensions BU3002SWCircuit block diagram Related productsK1L-D-06051B