Omron BU3002SW, BU1002SW Start and stop procedures and basic operation, Start procedure

Page 38

3. Operation

3-2 Start and stop procedures and basic operation

When the power switch is OFF and the AC input plug is connected to a commercial power supply:

The details of the most recent error are displayed. (item 4 on page 40)

The status indicator displays " ".

Power output is stopped.

The battery automatically starts recharging.

Start procedure

Operation Turn on the power switch of the UPS.

Output begins in Bypass Mode about 10 seconds after the switch is activated. (Status indicator “ ”)

However, “ ” is displayed at cold start, and output begins in Battery Mode.

The status indicator displays “ ”, and the self-diagnostic test is performed in Battery Mode for about 10 seconds. (If the battery voltage is low, the self-diagnostic test is not performed. It is automatically executed after the battery is charged.)

*1 When the self-diagnostic test finishes successfully, switching to AC output from commercial power is performed and normal operation starts.

*2 Self-diagnostic test is not performed at cold start.

If the self-diagnostic test is finished normally, It is replaced by the AC output from a commercial power supply and become a normal driving state through inverter mode.

If the self-diagnostic test is not executed, the UPS immediately starts outputting AC from commercial power.

Status indicator

 

Beep

None

Power supply output receptacles

Outputs power (connected devices are powered)

See also Cold start ON/OFF setting Page 49

• During operation, the battery is charged automatically.

AC input

ON

OFF

7 seg.

Power supply SW

ON

OFF

 

Power supply

ON

 

output lamp

OFF

Bypass operation

ON

 

lamp

OFF

Commercial Power

Operating mode

Battery

 

Operating mode

Bypass

Inverter

 

 

Commercial Power

Output

Battery

 

D-1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Bypass

Self-diagnostic

 

Commercial

 

 

 

Startup

 

 

 

 

 

 

mode

test

 

operation

 

 

 

preparation

 

 

 

 

 

 

 

 

 

 

 

 

1 sec.

about

 

about

about

 

 

 

10 sec.

 

2 to 3 sec.

10 sec.

 

 

 

<Note>

D-1 : The most recently displayed error code (refer to item 4 on page 34) (If no errors have occurred, " " is displayed.)

36

Image 38
Contents BU1002SW/BU3002SW Introduction Internal Battery Procedure from installation to operation Start Installation/connectionTable of Contents Misuse may cause death or serious injury Safety precautionsKeep plastic package bags out of reach of children Do not pinch or tie the cable of the unit Provide secure groundingDo not disassemble, repair, or modify the unit Doing so may compromise the safety of devices Do not allow the unit to come in contact with water If fluid leaks from the unit, do not touch the fluidUse a specified battery for replacement Do not insert metal objects into the battery connectorsPerform replacement on a stable and flat place Do not disassemble or modify the batteryDo not put the battery into fire and do not break it Do not use a new battery and an old battery at the same timeDo not perform a withstand voltage test Scheduled operation using the UPS monitoring software Quitting Battery ModeRebooting This unit uses lead acid batteriesUnpacking the product 2Checking the contentsPreparation Name of each part Front viewSide view Rear view BU1002SW BU3002SWExplanation of symbols used on unit Installation and connection Precautions and notes on installation and connectionDo not install the unit in other than specified orientations Installation and connection Do not perform a withstand voltage test Installation and connection BU1002SWBU3002SW Casters locked Connecting the equipment Group control of power supply outputConnecting a device to the power supply output BU1002SW Output on Output OFFNfpa Input plug L6-15P Front view Connecting a device to the power supply output BU3002SW BU3002SW Rated value of output capacity Max kVA/2100WRear panel Input plug L6-20P Front view Bring all the connected devices into operation Turn on the units power switchChecking the operation Battery Mode, check the units LED display and beep sound OFFRecharging the battery Charging the batteryMeasuring the initial value of backup time Precautions and notes for operation OperationExplanation Operation Turn on the power switch of the UPS Start and stop procedures and basic operationStart procedure Operation after a power failure Setting switch 1 can be used to turn the beeper ON/OFF.Connection capacity/battery level meter Operation during recovery from a power failureStop procedure Interpreting beeps and displays Displays and beeps in normal operationDisplay and beep for battery replacement Self-diagnosis test UPS functionsSuspending a beep Description of the auto battery test function Changing the setting of the functionsSetting switch function list UPS functions BS signal reception time corresponds to the setting switch BS signal valid range setting setting switch Settable items and explanations UPS operation mode settingsSettings available for this operation are shown below OFF Settings Cold start Estimated backup time Measuring the backup timeHow to measure backup time For Windows Server 2003/XP/Me/2000/Windows NT/Linux/MacBUM100S Life of battery estimated replacement timing Maintenance and InspectionChecking the battery Methods for checking the batteryReplacing the battery Battery recycling Procedure for recycling the batteryDo not hold the connector or cable of the battery pack Tighten the 2 screws Battery replacement is now complete Red tape Tighten 2 screws After replacing the battery during operation Replacing the fan Do not put your fingers into the fanFan replacement procedure Cleaning Cleaning the UPSUsing the UPS monitoring software and contact signal UPS monitoring softwareSoftware title Connect the UPS to a computer RS-232CWhen using UPS Power Manager UPS monitoring software for Mac When connecting 2 or more computers to the UPSExplanation Install the included UPS service driver on the computer Connector Perform UPS service setup ClickRecycling and Discarding the Battery Stopping the UPSHow to set up UPS service set the time to shut down Windows Check Set ClickCheck Set Check Set Signal output Contact signalContact Signal Low battery level signal output BLItems that can be set using the contact signal card Remote ON/OFF SignalOutput delay time setting for backup signal output BU BU/BL signal reverse output settingInsert/ removal method of contact signal card Contact Signal Connector female DSUB9PContact Signal circuit inside the UPS Remote ON/OFF connectorContact Signal ratings Example of the use of the Contact Signal circuitPrecautions and notes for the use of the Contact Signal Remote ON/OFF circuitUsing an SNMP/Web card Adding an SNMP/Web cardSNMP/Web card outline Description featuresSpecifications Extending the backup time Connecting an additional battery unitAdding BUM300S to the BU3002SW Troubleshooting Problem Check and remedySpecifications ReferencesDimensions BU3002SWCircuit block diagram Related productsK1L-D-06051B