GE A8950CC installation instructions Main Local Optics Info, Main Local Video Input Mapping

Page 33

Main -> Local -> Optics -> Info:

Optic Info: ABCD

Wavelength: 1310 nM

Max Distance: 15 km

Vendor: Infineon

The Info Menu shows the wavelength (normally 1310nM), maximum distance (normally 15km) and optic transceiver vendor name (Infineon) for the selected optic transceiver. Use the "+" button to select the next transceiver. Use the "-" button to select the previous transceiver.

Main -> Local -> Video:

Video Menu

1. Input Mapping

2.Output Mapping

3.Test Select

Video Input and Video Output mapping, monitoring, and tests can be accessed from the sub-menus.

Main -> Local -> Video -> Input Mapping:

Video:	A		B
	A		B
Exit	1	1	1

This screen allows you to assign a video input channel to a video output channel over a selected fiber port. The camera icon in the middle of the screen indicates the presence of a video signal for the selected channel. If the camera has an X through it, video is not present on this channel. If the camera does not have an X through it, then video is present. The number under the camera icon indicates the currently selected input channel. The numbers under the monitor icons to the left and/or right of the camera represent the output channel numbers. The arrows to the left and/or right of the camera (labeled A and B, respectively) indicate over which fibers this mapping is enabled. If the selected input channel is mapped to the output channel then a black square is shown in the middle of the monitor icon and the arrow is displayed. If a mapping does not exist for this input and output channel pair, then the monitor icon

is blank and the arrow is not shown.

Use the "left" and "right" button to move the cursor at the bottom of the screen. Use "+" and "-" to increment and decrement the channel numbers. Incrementing the input channel automatically increments both output channels. Press "enter" while the cursor is at an output channel to enable a mapping. Move the cursor to "Exit" and press enter to leave this screen. All channel mapping are saved when you leave this menu.

31

Image 33

Contents Installation instructions Installation Instructions Intended Use Before You BeginCustomer Support Conventions Used in this ManualModule Installation Installing Power SuppliesGetting Started OverviewInstallation instructions Installing the Optical Transceiver ModuleTools and materials required Connect fiberPoint-to-Point Connect Repeater ConnectSelf-Healing Connect Optic LED LED operating statusInstalling the Data Module Configure data moduleSetting Mode Connect Install data moduleFiber Link Data Connections Using the breakout boxPin Signal Data module channel sequence RS-485 4-WIRE InterfaceInstall the Ethernet module Installing the Ethernet ModuleConfigure Installing the Video Module Install video input moduleInstall video output module Connection instructions Video InputsVideo Outputs Video Output module channel sequence Video Input module channel sequenceConfigure audio module Installing the Audio ModuleChannel sequence is as follows Installing audio modulesConnecting to audio modules Terminal Block Pin Assignments Audio module channel sequenceInstall contact closure module Installing the Contact Closure ModuleRJ45 Socket Viewed from the rear of the unit Connect to the moduleContact Input module channel sequence Configuring the Phoenix Fiber Optic Communications System Select the system topology Turn on power and check statusGE Security Set the Node ID Front Panel Menu Tree and Descriptions Main Menu Main LocalMain Local Node Main Local Node Topology Main Local Node IDMain Local Optics Main Local Node Load DefaultsMain Local Optics Transmit Main Local Optics ReceiveMain Local Optics Info Main Local VideoMain Local Video Input Mapping Main Local Video Output Mapping Video Test Channel Test Off Format Ntsc Main Local Data Input Mapping Main Local DataMain Local Data Output Mapping Main Local Data Format Select Main Local Ethernet Port Status Main Local EthernetMain Local -Ethernet Port Control Main Local -Ethernet Port TrafficMain Local Audio Main Local Audio Input MappingMain Local Audio Output Mapping Main Local Audio Test Main Local ContactsMain Local Contacts Input Mapping Main Local Contacts Output Mapping Main Local Contacts ConfigureMain Local Test Main Local PowerMain Local Test Temp Main Local Test LED/LCD/AlarmMain Local Test Video Main Local Test DataMain About Main RemoteOverview Limited warranty Blank Panel Installation and SpecificationsProduct ordering Optical Transceiver Module SpecificationsData Data Module SpecificationsEthernet Ethernet Module SpecificationsVideo Video Module SpecificationsProduct 0rdering Audio Module SpecificationsContacts / Relays Contact Closure Module Specifications