GE A8950CC Installing the Data Module, Configure data module, Setting Mode

Page 8

Installing the Data Module

Overview

The Phoenix A8910MPD data module is capable of inserting/extracting

4 channels of multiprotocol serial data (MPD) per module. With a maximum of four cards per node, the system capacity is 16 channels. Each channel is capable of transmitting and receiving serial data throughout the Phoenix system. The card is not limited to any single data type so that various formats can be mixed on a single card. As with other GE Security MPD products, data translation capabilities are included.

Tools and materials required

The data modules are held in place with simple thumbscrews with screwdriver slots. The only tool recommended is a small flat blade screwdriver.

Installation instructions:

1. Configure data module:

Prior to installation, you must specify the appropriate data format using the rotary switches on the module. For each channel on the data module, rotate the dial switch to the desired format. If you want to select the data format from the front panel, leave the switch in position 0.

Setting

Mode

Setting

Mode

0

Software-selectable (factory preset)

8

RS-485 2-wire 2 V

1

RS-232 (3-wire)

9

RS-485 4-wire standard

2

RS-232 + handshake

A

RS-485 4-wire 1 V

3

TTL

B

RS-485 4-wire 2 V

4

RS-422 2-wire

C

Reserved

5

Manchester/biphase

D

Reserved

6

RS-485 2-wire standard/Sensornet

E

Reserved

7

RS-485 2-wire 1V

F

Test Mode

NOTE: The DATA SELECT switches are shipped in the Software-Selectable setting.

As with all GE Security MPD products, data translation can easily be accomplished using the table information below.

Translation

Input

Output

Comment

 

 

TTL

 

 

 

 

 

RS-232, 3-wire

3

1

Signal level conversion.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RS-232, 3-wire

 

TTL

1

3

Signal level conversion.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TTL

 

 

 

RS-422

 

 

3

4

Single ended to differential conversion.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RS-422

 

 

 

 

 

TTL-wire

4

3

Differential to single ended conversion.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RS-232, 3-wire

 

RS-422

1

4

Single ended to differential conversion.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RS-422

 

 

 

 

 

RS-232, 3-wire

4

1

Differential to single ended conversion.

 

 

 

 

 

 

 

 

 

 

RS-232, 5-wire

 

RS-485

2

7 - A

RS232 Handshaking bit is used to indicate Tri-state.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RS-485

 

 

 

 

 

RS-232, 5-wire

7 - A

2

Tri-state detection circuitry activates handshaking bit.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Installation instructions Installation Instructions Before You Begin Intended UseCustomer Support Conventions Used in this ManualInstalling Power Supplies Module InstallationGetting Started OverviewInstalling the Optical Transceiver Module Installation instructionsTools and materials required Connect fiberSelf-Healing Connect Point-to-Point ConnectRepeater Connect LED operating status Optic LEDSetting Mode Installing the Data ModuleConfigure data module Install data module ConnectUsing the breakout box Fiber Link Data ConnectionsPin Signal RS-485 4-WIRE Interface Data module channel sequenceInstalling the Ethernet Module Install the Ethernet moduleConfigure Install video output module Installing the Video ModuleInstall video input module Video Outputs Connection instructionsVideo Inputs Video Input module channel sequence Video Output module channel sequenceInstalling the Audio Module Configure audio moduleInstalling audio modules Channel sequence is as followsConnecting to audio modules Audio module channel sequence Terminal Block Pin AssignmentsInstalling the Contact Closure Module Install contact closure moduleConnect to the module RJ45 Socket Viewed from the rear of the unitContact Input module channel sequence Configuring the Phoenix Fiber Optic Communications System Turn on power and check status Select the system topologyGE Security Set the Node ID Front Panel Menu Tree and Descriptions Main Local Node Main MenuMain Local Main Local Node ID Main Local Node TopologyMain Local Node Load Defaults Main Local OpticsMain Local Optics Transmit Main Local Optics ReceiveMain Local Video Input Mapping Main Local Optics InfoMain Local Video Main Local Video Output Mapping Video Test Channel Test Off Format Ntsc Main Local Data Main Local Data Input MappingMain Local Data Output Mapping Main Local Data Format Select Main Local Ethernet Main Local Ethernet Port StatusMain Local -Ethernet Port Control Main Local -Ethernet Port TrafficMain Local Audio Output Mapping Main Local AudioMain Local Audio Input Mapping Main Local Contacts Input Mapping Main Local Audio TestMain Local Contacts Main Local Contacts Configure Main Local Contacts Output MappingMain Local Power Main Local TestMain Local Test LED/LCD/Alarm Main Local Test TempMain Local Test Video Main Local Test DataMain Remote Main AboutBlank Panel Installation and Specifications Overview Limited warrantyOptical Transceiver Module Specifications Product orderingData Module Specifications DataEthernet Module Specifications EthernetVideo Module Specifications VideoAudio Module Specifications Product 0rderingContact Closure Module Specifications Contacts / Relays
Top Page Image Contents