Freescale Semiconductor MMDS0508 manual Configuring the Platform Board, Factory Test Header J1

Page 11

Freescale Semiconductor, Inc.

Installation

Configuring the Platform Board

Figure 2.2 M68MMDS0508 Station Module (Left Side)

Panel

Power Cord

Socket

Power Switch

9-Pin Serial

Connector

+5V Out

2.2 Configuring the Platform Board

The MMDS platform board has four jumper headers, all located near the front. Jumper header J1 is for factory test. Jumper headers J2, J3, and J4 control the voltage levels for ports A through D.

NOTE

Before shipping the MMDS, factory personnel configure the

 

platform board correctly for virtually all users. You should not

 

reconfigure platform-board headers unless your EM user’s manual

 

tells you to.

 

 

2.2.1 Factory Test Header (J1)

The diagram in Figure 2.3 shows the factory configuration of jumper header J1. The jumper between pins 1 and 2 is correct for MMDS operation.

MMDS0508 Target Interface

2–11

For More Information: www.freescale.com

Image 11
Contents Freescale Semiconductor, Inc MMDS0508 Target InterfaceHow to Contact Metrowerks Table of Contents Appendix Introduction Mmds FeaturesSystem Components Freescale Semiconductor, Inc System Components MMDS0508 Target Interface Installation M68MMDS0508 Station Module Right Side Factory Test Header J1 Configuring the Platform BoardFactory Test Header J1 Port Voltage Control Headers J2-J4Removing the EM Installing the EMBus State Analyzer Connection Making Cable ConnectionsHost Computer Connection Target Cable Connection Power ConnectionMaking Cable Connections MMDS0508 Target Interface RS232 Serial Connector Reset SwitchSerial Connector and Cable Pin Assignments Logic Cables and ConnectorsPod and Logic Cable Pin Assignments Power Switch/Connector Assembly Power Supply Fuse ReplacementFreescale Semiconductor, Inc Power Supply Fuse Replacement MMDS0508 Target Interface Mmds Target Component MMDS0508 ConfigurationGeneral Interfacing Your System and the Target Definitions, Acronyms and AbbreviationsHardware connection Loading the MMDS0508 TargetLoading MotoSIL Target Communication ConfigurationMotoSIL Communication Configuration Communication Device SpecificationData Format Debugger Status Bar forMMDS0508 Menu Entries Communication Communication Baud RateShow Protocol Memory ConfigurationMaximum Baud Rate 0nnnnVxx.MEM Personality .MEM Files12 Error Message Memory Signals EmulationDual-Port RAM MCU Clock ResetBus Tracing Comdev Default Target SetupMotorola ESL Parameters Showprot Bus AnalyzerIntroduction to the Bus Analyzer BaudrateTrace Buffer Using the Bus AnalyzerWatchpoints Trace Modes15 Bus Analyzer Trace window popup menu17 Bus Analyzer Trigger Setup Trigger SetupSequencer Setup Continuous All Cycles Non-Triggered ModesCounted Modes Triggered Modes/Sequential Event ModeCounted/Sequential Recording Mode Clock Frequency Time Tag Clock SetupCollecting Data View Cycles Viewing Collected DataRecording Bus Data Trigger EventEvents Textual DisplayTime Measuring Control SignalsInstructions Only Display Time TagZoom In or Out Graphical Display22 Trace Zoom Display Add / Remove Items in the Trace Window ShowLocationSearch for a Frame Scrolling the DisplayBackward Search for EventsOK Button ForwardPrevious Event Search for a PatternPrevious Pattern Cancel ButtonNext Pattern Dump File Dumping the Bus analyzer data to a file31 Analyzer Dump Only Frame Syntax Mmds CommandsBaud Rate Command Short DescriptionTrigger Commands Set trigger Data RED ORG YEL GRN Examples Disables triggers a and B Bus Analyzer Commands Darm GP B Log trace Open the logging file Sets the 8 Mhz oscillator as the time tag clock source Address SP 8 Set sequencer Display time tag difference VA MODE=MIX INS Graph Reset Commands Target Signal Emulation CommandsOther Commands MEM OSC Protocol Disables the real time memory block Index IDX-84 MMDS0508 Target Interface IDX-85 IDX-86