Freescale Semiconductor MMDS0508 manual How to Contact Metrowerks

Page 2

Freescale Semiconductor, Inc.

Metrowerks, the Metrowerks logo, and CodeWarrior are registered trademarks of Metrowerks Corp. in the US and/or other countries. All other tradenames and trademarks are the property of their respective owners.

Copyright © Metrowerks Corporation. 2002. ALL RIGHTS RESERVED.

The reproduction and use of this document and related materials are governed by a license agreement between Metrowerks Corp. and its licensee. Consult that license agreement before use or reproduction of any portion of this document. If you do not have a copy of the license agreement, contact your Metrowerks representative or call 800-377-5416.

Metrowerks reserves the right to make changes to any product described or referred to in this doc- ument without further notice. Metrowerks makes no warranty, representation or guarantee regard- ing the merchantability or fitness of its products for any particular purpose, nor does Metrowerks assume any liability arising out of the application or use of any product described herein and spe- cifically disclaims any and all liability. Metrowerks software is not authorized for and has not been designed, tested, manufactured, or intended for use in developing applications where the failure, malfunction, or any inaccuracy of the application carries a risk of death, serious bodily injury, or damage to tangible property, including, but not limited to, use in factory control systems, medical devices or facilities, nuclear facilities, aircraft or automobile navi- gation or communication, emergency systems, or other applications with a similar degree of potential hazard.

Documentation stored on electronic media may be printed for non-commercial personal use only, further to the license agreement related to the product associated with the documentation. Subject to the foregoing non-commercial personal use, no portion of this documentation may be repro- duced or transmitted in any form or by any means, electronic or mechanical, without prior written permission from Metrowerks.

USE OF ALL SOFTWARE, DOCUMENTATION AND RELATED MATERIALS ARE SUB- JECT TO THE METROWERKS END USER LICENSE AGREEMENT FOR SUCH PRODUCT.

How to Contact Metrowerks

Corporate Headquarters

Metrowerks Corporation

 

9801 Metric Blvd.

 

Austin, TX 78758

 

U.S.A.

 

 

World Wide Web

http://www.metrowerks.com

 

 

Ordering & Technical Support

Voice: (800) 377-5416

 

Fax: (512) 997-4901

 

 

For More Information: www.freescale.com

Image 2
Contents MMDS0508 Target Interface Freescale Semiconductor, IncHow to Contact Metrowerks Table of Contents Appendix Mmds Features IntroductionSystem Components Freescale Semiconductor, Inc System Components MMDS0508 Target Interface Installation M68MMDS0508 Station Module Right Side Configuring the Platform Board Factory Test Header J1Port Voltage Control Headers J2-J4 Factory Test Header J1Installing the EM Removing the EMBus State Analyzer Connection Making Cable ConnectionsHost Computer Connection Power Connection Target Cable ConnectionMaking Cable Connections MMDS0508 Target Interface Reset Switch RS232 Serial ConnectorLogic Cables and Connectors Serial Connector and Cable Pin AssignmentsPod and Logic Cable Pin Assignments Power Supply Fuse Replacement Power Switch/Connector AssemblyFreescale Semiconductor, Inc Power Supply Fuse Replacement MMDS0508 Target Interface Mmds Target Component MMDS0508 ConfigurationGeneral Definitions, Acronyms and Abbreviations Interfacing Your System and the TargetLoading the MMDS0508 Target Hardware connectionCommunication Configuration Loading MotoSIL TargetCommunication Device Specification MotoSIL Communication ConfigurationData Format Debugger Status Bar forMMDS0508 Menu Entries Communication Baud Rate CommunicationShow Protocol Memory ConfigurationMaximum Baud Rate Personality .MEM Files 0nnnnVxx.MEM12 Error Message Memory Signals EmulationDual-Port RAM MCU Clock ResetBus Tracing Comdev Default Target SetupMotorola ESL Parameters Baudrate Bus AnalyzerIntroduction to the Bus Analyzer ShowprotTrace Modes Using the Bus AnalyzerWatchpoints Trace BufferTrace window popup menu 15 Bus AnalyzerTrigger Setup 17 Bus Analyzer Trigger SetupSequencer Setup Non-Triggered Modes Continuous All CyclesTriggered Modes/Sequential Event Mode Counted ModesCounted/Sequential Recording Mode Time Tag Clock Setup Clock FrequencyCollecting Data Trigger Event Viewing Collected DataRecording Bus Data View CyclesTextual Display EventsTime Tag Control SignalsInstructions Only Display Time MeasuringGraphical Display Zoom In or Out22 Trace Zoom Display ShowLocation Add / Remove Items in the Trace WindowScrolling the Display Search for a FrameForward Search for EventsOK Button BackwardSearch for a Pattern Previous EventPrevious Pattern Cancel ButtonNext Pattern Dumping the Bus analyzer data to a file Dump File31 Analyzer Dump Only Frame Short Description Mmds CommandsBaud Rate Command SyntaxTrigger Commands Set trigger Data RED ORG YEL GRN Examples Disables triggers a and B Bus Analyzer Commands Darm GP B Log trace Open the logging file Sets the 8 Mhz oscillator as the time tag clock source Address SP 8 Set sequencer Display time tag difference VA MODE=MIX INS Graph Target Signal Emulation Commands Reset CommandsOther Commands MEM OSC Protocol Disables the real time memory block Index IDX-84 MMDS0508 Target Interface IDX-85 IDX-86