Freescale Semiconductor manual Debugger Status Bar for, MMDS0508 Menu Entries, Data Format

Page 29

 

 

Freescale Semiconductor, Inc.

 

 

MMDS Target Component

 

 

4.7 The Debugger Status Bar for the MMDS

 

 

 

 

 

 

 

NOTE

Saving the communication device and the baud rate through this

 

 

 

dialog box overrides environment variables BAUDRATE and

 

 

COMDEV of the default.env file.

 

 

 

 

4.6.2 Data Format

The MMDS0508 data format is 8 data bits, 1 stop bit, no parity, and a variable baud rate. The default speed is 9600 baud, unless you change this default via the menu selection MMDS0508>Communication....

Communication speeds of 1200 through 115200 baud are available, depending on the host-computer hardware.

4.7The Debugger Status Bar for the

MMDS

Once you have loaded the MMDS Target Component, the debugger status bar gives specific information as shown in Figure 4.8:

Figure 4.8 The Debugger Status Bar

From left to right, this information is: the serial-communication baud rate, the debugger running mode, the BUS analyzer mode, the MCU name (depending on the MCU-Id), and the debugger status.

4.8 MMDS0508 Menu Entries

The Figure 4.9 show the MMDS0508 Menu Entries:

MMDS0508 Target Interface

4–29

For More Information: www.freescale.com

Image 29
Contents Freescale Semiconductor, Inc MMDS0508 Target InterfaceHow to Contact Metrowerks Table of Contents Appendix Introduction Mmds FeaturesSystem Components Freescale Semiconductor, Inc System Components MMDS0508 Target Interface Installation M68MMDS0508 Station Module Right Side Factory Test Header J1 Configuring the Platform BoardFactory Test Header J1 Port Voltage Control Headers J2-J4Removing the EM Installing the EMBus State Analyzer Connection Making Cable ConnectionsHost Computer Connection Target Cable Connection Power ConnectionMaking Cable Connections MMDS0508 Target Interface RS232 Serial Connector Reset SwitchSerial Connector and Cable Pin Assignments Logic Cables and ConnectorsPod and Logic Cable Pin Assignments Power Switch/Connector Assembly Power Supply Fuse ReplacementFreescale Semiconductor, Inc Power Supply Fuse Replacement MMDS0508 Target Interface Mmds Target Component MMDS0508 ConfigurationGeneral Interfacing Your System and the Target Definitions, Acronyms and AbbreviationsHardware connection Loading the MMDS0508 TargetLoading MotoSIL Target Communication ConfigurationMotoSIL Communication Configuration Communication Device SpecificationData Format Debugger Status Bar forMMDS0508 Menu Entries Communication Communication Baud RateShow Protocol Memory ConfigurationMaximum Baud Rate 0nnnnVxx.MEM Personality .MEM Files12 Error Message Memory Signals EmulationDual-Port RAM MCU Clock ResetBus Tracing Comdev Default Target SetupMotorola ESL Parameters Introduction to the Bus Analyzer Bus AnalyzerBaudrate ShowprotWatchpoints Using the Bus AnalyzerTrace Modes Trace Buffer15 Bus Analyzer Trace window popup menu17 Bus Analyzer Trigger Setup Trigger SetupSequencer Setup Continuous All Cycles Non-Triggered ModesCounted Modes Triggered Modes/Sequential Event ModeCounted/Sequential Recording Mode Clock Frequency Time Tag Clock SetupCollecting Data Recording Bus Data Viewing Collected DataTrigger Event View CyclesEvents Textual DisplayInstructions Only Display Control SignalsTime Tag Time MeasuringZoom In or Out Graphical Display22 Trace Zoom Display Add / Remove Items in the Trace Window ShowLocationSearch for a Frame Scrolling the DisplayOK Button Search for EventsForward BackwardPrevious Event Search for a PatternPrevious Pattern Cancel ButtonNext Pattern Dump File Dumping the Bus analyzer data to a file31 Analyzer Dump Only Frame Baud Rate Command Mmds CommandsShort Description SyntaxTrigger Commands Set trigger Data RED ORG YEL GRN Examples Disables triggers a and B Bus Analyzer Commands Darm GP B Log trace Open the logging file Sets the 8 Mhz oscillator as the time tag clock source Address SP 8 Set sequencer Display time tag difference VA MODE=MIX INS Graph Reset Commands Target Signal Emulation CommandsOther Commands MEM OSC Protocol Disables the real time memory block Index IDX-84 MMDS0508 Target Interface IDX-85 IDX-86