Freescale Semiconductor MMDS0508 manual Personality .MEM Files, 0nnnnVxx.MEM

Page 32

Freescale Semiconductor, Inc.

MMDS Target Component

4.8 MMDS0508 Menu Entries

Figure 4.11 Memory Configuration

This dialog box shows the target’s memory setup. The system automatically loads this setup if you check the Auto select according to MCU-Idcheckbox. The debugger identifies and sets the memory map through the processor MCU-Id. To open another configuration, click the Open button. To save modifications to the current configuration, click the Save... button.

4.8.3 Personality (.MEM) Files

For proper operation, the Motosil target must load the personality file (.MEM file) that matches the connected Emulation Module (EM).

The .MEM file filename format is:

0nnnnVxx.MEM

where ‘nnnn’ is the four-digit, hexadecimal ‘MCU-Id’ number of the MCU, and ‘xx’ is a two-digit version number.

If the target cannot find this file, or if the file is not valid, the Error message box appears as shown in Figure 4.12:

4–32	MMDS0508 Target Interface

For More Information: www.freescale.com

Image 32

Contents MMDS0508 Target Interface Freescale Semiconductor, IncHow to Contact Metrowerks Table of Contents Appendix Mmds Features IntroductionSystem Components Freescale Semiconductor, Inc System Components MMDS0508 Target Interface Installation M68MMDS0508 Station Module Right Side Configuring the Platform Board Factory Test Header J1Port Voltage Control Headers J2-J4 Factory Test Header J1Installing the EM Removing the EMBus State Analyzer Connection Making Cable ConnectionsHost Computer Connection Power Connection Target Cable ConnectionMaking Cable Connections MMDS0508 Target Interface Reset Switch RS232 Serial ConnectorLogic Cables and Connectors Serial Connector and Cable Pin AssignmentsPod and Logic Cable Pin Assignments Power Supply Fuse Replacement Power Switch/Connector AssemblyFreescale Semiconductor, Inc Power Supply Fuse Replacement MMDS0508 Target Interface Mmds Target Component MMDS0508 ConfigurationGeneral Definitions, Acronyms and Abbreviations Interfacing Your System and the TargetLoading the MMDS0508 Target Hardware connectionCommunication Configuration Loading MotoSIL TargetCommunication Device Specification MotoSIL Communication ConfigurationData Format Debugger Status Bar forMMDS0508 Menu Entries Communication Baud Rate CommunicationShow Protocol Memory ConfigurationMaximum Baud Rate Personality .MEM Files 0nnnnVxx.MEM12 Error Message Memory Signals EmulationDual-Port RAM MCU Clock ResetBus Tracing Comdev Default Target SetupMotorola ESL Parameters Bus Analyzer Introduction to the Bus AnalyzerBaudrate ShowprotUsing the Bus Analyzer WatchpointsTrace Modes Trace BufferTrace window popup menu 15 Bus AnalyzerTrigger Setup 17 Bus Analyzer Trigger SetupSequencer Setup Non-Triggered Modes Continuous All CyclesTriggered Modes/Sequential Event Mode Counted ModesCounted/Sequential Recording Mode Time Tag Clock Setup Clock FrequencyCollecting Data Viewing Collected Data Recording Bus DataTrigger Event View CyclesTextual Display EventsControl Signals Instructions Only DisplayTime Tag Time MeasuringGraphical Display Zoom In or Out22 Trace Zoom Display ShowLocation Add / Remove Items in the Trace WindowScrolling the Display Search for a FrameSearch for Events OK ButtonForward BackwardSearch for a Pattern Previous EventPrevious Pattern Cancel ButtonNext Pattern Dumping the Bus analyzer data to a file Dump File31 Analyzer Dump Only Frame Mmds Commands Baud Rate CommandShort Description SyntaxTrigger Commands Set trigger Data RED ORG YEL GRN Examples Disables triggers a and B Bus Analyzer Commands Darm GP B Log trace Open the logging file Sets the 8 Mhz oscillator as the time tag clock source Address SP 8 Set sequencer Display time tag difference VA MODE=MIX INS Graph Target Signal Emulation Commands Reset CommandsOther Commands MEM OSC Protocol Disables the real time memory block Index IDX-84 MMDS0508 Target Interface IDX-85 IDX-86