Freescale Semiconductor MMDS0508 manual Mem

Page 79

Freescale Semiconductor, Inc.

Appendix

MMDS Commands

A.1.6.3 Description

The LOADMAP command loads a memory map from a file. The file specification must be the full pathname. If the file is in the current directory, the characters “.\” must precede the name (for example: LOADMAP .\00123V22.MEM).

Example:

LOADMAP 0xC17

Loads a memory map from a file that matches this MCU identifier (68HC08AX48).

Note that the MCUID identifies an MCU, not an EM Board. The memory map filename has this format:

0nnnnVvv.MEM

where ‘nnnn’ is the four-digit, hexadecimal ‘MCU-ID’, and ‘vv’ is a two-digit version number.

MEM

A.1.6.4 Short Description

displays the memory map.

A.1.6.5 Syntax

MEM

A.1.6.6 Description

The MEM command displays the current memory map.

Example:

in>MEM
Type	Addresses		Comment
-------------------------------------------------------
IO	0..	3F	PRU or TOP	TOP board resource or the PRU
NONE	40..	4F	NONE
RAM	50.. 64F		RAM
NONE	650.. 7FF		NONE
EEPROM	800.. A7F		EEPROM
NONE	A80..3DFF		NONE

MMDS0508 Target Interface				A–79

For More Information: www.freescale.com

Image 79

Contents Freescale Semiconductor, Inc MMDS0508 Target InterfaceHow to Contact Metrowerks Table of Contents Appendix Introduction Mmds FeaturesSystem Components Freescale Semiconductor, Inc System Components MMDS0508 Target Interface Installation M68MMDS0508 Station Module Right Side Factory Test Header J1 Configuring the Platform BoardFactory Test Header J1 Port Voltage Control Headers J2-J4Removing the EM Installing the EMHost Computer Connection Making Cable ConnectionsBus State Analyzer Connection Target Cable Connection Power ConnectionMaking Cable Connections MMDS0508 Target Interface RS232 Serial Connector Reset SwitchSerial Connector and Cable Pin Assignments Logic Cables and ConnectorsPod and Logic Cable Pin Assignments Power Switch/Connector Assembly Power Supply Fuse ReplacementFreescale Semiconductor, Inc Power Supply Fuse Replacement MMDS0508 Target Interface Mmds Target Component General ConfigurationMMDS0508 Interfacing Your System and the Target Definitions, Acronyms and AbbreviationsHardware connection Loading the MMDS0508 TargetLoading MotoSIL Target Communication ConfigurationMotoSIL Communication Configuration Communication Device SpecificationMMDS0508 Menu Entries Debugger Status Bar forData Format Communication Communication Baud RateMaximum Baud Rate Memory ConfigurationShow Protocol 0nnnnVxx.MEM Personality .MEM Files12 Error Message Dual-Port RAM Signals EmulationMemory Bus Tracing ResetMCU Clock Motorola ESL Parameters Default Target SetupComdev Showprot Bus AnalyzerIntroduction to the Bus Analyzer BaudrateTrace Buffer Using the Bus AnalyzerWatchpoints Trace Modes15 Bus Analyzer Trace window popup menu17 Bus Analyzer Trigger Setup Trigger SetupSequencer Setup Continuous All Cycles Non-Triggered ModesCounted Modes Triggered Modes/Sequential Event ModeCounted/Sequential Recording Mode Clock Frequency Time Tag Clock SetupCollecting Data View Cycles Viewing Collected DataRecording Bus Data Trigger EventEvents Textual DisplayTime Measuring Control SignalsInstructions Only Display Time TagZoom In or Out Graphical Display22 Trace Zoom Display Add / Remove Items in the Trace Window ShowLocationSearch for a Frame Scrolling the DisplayBackward Search for EventsOK Button ForwardPrevious Event Search for a PatternNext Pattern Cancel ButtonPrevious Pattern Dump File Dumping the Bus analyzer data to a file31 Analyzer Dump Only Frame Syntax Mmds CommandsBaud Rate Command Short DescriptionTrigger Commands Set trigger Data RED ORG YEL GRN Examples Disables triggers a and B Bus Analyzer Commands Darm GP B Log trace Open the logging file Sets the 8 Mhz oscillator as the time tag clock source Address SP 8 Set sequencer Display time tag difference VA MODE=MIX INS Graph Reset Commands Target Signal Emulation CommandsOther Commands MEM OSC Protocol Disables the real time memory block Index IDX-84 MMDS0508 Target Interface IDX-85 IDX-86