Freescale Semiconductor MMDS0508 manual General, Configuration

Page 24

Freescale Semiconductor, Inc.

MMDS Target Component

4.2 General

4.2 General

This chapter describes the specific features of the MMDS0508, including emulation memory mapping, as well as the function and purpose of the bus analyzer. The explanations of windows and dialog boxes are with the explanations of corresponding MMDS0508 features.

4.2.1 MMDS0508

The MMDS0508 is an emulator system, for CPU05 or CPU08 MCUs, that provides emulation memory and a bus state analyzer.

4.2.2 Configuration

The functions above are specific for the MMDS0508, so are available only with this emulator component. To use these features select the corresponding menu commands shown in Figure 4.1, such as MMDS0508 > ...

Figure 4.1 MMDS0508 Menu

These functions are part of the MMDS0508 Motorola Modular Development System. Their supporting libraries consist of dialog boxes and routines to interface the debugger and the hardware.

4–24	MMDS0508 Target Interface

For More Information: www.freescale.com

Image 24

Contents MMDS0508 Target Interface Freescale Semiconductor, IncHow to Contact Metrowerks Table of Contents Appendix Mmds Features IntroductionSystem Components Freescale Semiconductor, Inc System Components MMDS0508 Target Interface Installation M68MMDS0508 Station Module Right Side Configuring the Platform Board Factory Test Header J1Port Voltage Control Headers J2-J4 Factory Test Header J1Installing the EM Removing the EMMaking Cable Connections Host Computer ConnectionBus State Analyzer Connection Power Connection Target Cable ConnectionMaking Cable Connections MMDS0508 Target Interface Reset Switch RS232 Serial ConnectorLogic Cables and Connectors Serial Connector and Cable Pin AssignmentsPod and Logic Cable Pin Assignments Power Supply Fuse Replacement Power Switch/Connector Assembly Freescale Semiconductor, Inc Power Supply Fuse Replacement MMDS0508 Target Interface Mmds Target Component Configuration GeneralMMDS0508 Definitions, Acronyms and Abbreviations Interfacing Your System and the TargetLoading the MMDS0508 Target Hardware connectionCommunication Configuration Loading MotoSIL TargetCommunication Device Specification MotoSIL Communication ConfigurationDebugger Status Bar for MMDS0508 Menu EntriesData Format Communication Baud Rate CommunicationMemory Configuration Maximum Baud RateShow Protocol Personality .MEM Files 0nnnnVxx.MEM12 Error Message Signals Emulation Dual-Port RAMMemory Reset Bus TracingMCU Clock Default Target Setup Motorola ESL ParametersComdev Bus Analyzer Introduction to the Bus AnalyzerBaudrate ShowprotUsing the Bus Analyzer WatchpointsTrace Modes Trace BufferTrace window popup menu 15 Bus AnalyzerTrigger Setup 17 Bus Analyzer Trigger SetupSequencer Setup Non-Triggered Modes Continuous All CyclesTriggered Modes/Sequential Event Mode Counted ModesCounted/Sequential Recording Mode Time Tag Clock Setup Clock FrequencyCollecting Data Viewing Collected Data Recording Bus DataTrigger Event View CyclesTextual Display EventsControl Signals Instructions Only DisplayTime Tag Time MeasuringGraphical Display Zoom In or Out22 Trace Zoom Display ShowLocation Add / Remove Items in the Trace WindowScrolling the Display Search for a FrameSearch for Events OK ButtonForward BackwardSearch for a Pattern Previous EventCancel Button Next PatternPrevious Pattern Dumping the Bus analyzer data to a file Dump File31 Analyzer Dump Only Frame Mmds Commands Baud Rate CommandShort Description SyntaxTrigger Commands Set trigger Data RED ORG YEL GRN Examples Disables triggers a and B Bus Analyzer Commands Darm GP B Log trace Open the logging file Sets the 8 Mhz oscillator as the time tag clock source Address SP 8 Set sequencer Display time tag difference VA MODE=MIX INS Graph Target Signal Emulation Commands Reset CommandsOther Commands MEM OSC Protocol Disables the real time memory block Index IDX-84 MMDS0508 Target Interface IDX-85 IDX-86