Freescale Semiconductor MMDS0508 manual Default Target Setup, Motorola ESL Parameters, Comdev

Page 36

Freescale Semiconductor, Inc.

MMDS Target Component

4.9 Default Target Setup

4.9 Default Target Setup

As with any target, you can use the Target menu to load the MMDS target component, or you can set the MMDS target component as a default in the PROJECT.INI file. This file should be in the project directory.

Example of PROJECT.INI file.
[DEFAULTS]
Window0=Source		0	0	50	40
Window1=Assembly		50	0	50	40
Window2=Register		50	40	50	30
Window3=Memory		50	70	50	30
Window4=Data		0	40	50	25
Window5=Command		0	65	50	20
Window6=Module		0	85	50	15
Target=Motosil
[Motorola ESL]
COMDEV=COM2
BAUDRATE=57600
SHOWPROT=1

NOTE	For more information about the PROJECT.INI file, please see the
	debugger manual.

4.9.1 Motorola ESL Parameters

In normal use, you set these parameters in the project.ini file once, interactively, during installation. You use these parameter values in subsequent debugging sessions.

4.9.1.1 COMDEV

This parameter specifies the host-computer communication port. COM1 is the default communication device for PCs. The default for UNIX systems is /dev/ttya.

4–36	MMDS0508 Target Interface

For More Information: www.freescale.com

Image 36

Contents MMDS0508 Target Interface Freescale Semiconductor, IncHow to Contact Metrowerks Table of Contents Appendix Mmds Features IntroductionSystem Components Freescale Semiconductor, Inc System Components MMDS0508 Target Interface Installation M68MMDS0508 Station Module Right Side Configuring the Platform Board Factory Test Header J1Port Voltage Control Headers J2-J4 Factory Test Header J1Installing the EM Removing the EMMaking Cable Connections Host Computer ConnectionBus State Analyzer Connection Power Connection Target Cable ConnectionMaking Cable Connections MMDS0508 Target Interface Reset Switch RS232 Serial ConnectorLogic Cables and Connectors Serial Connector and Cable Pin AssignmentsPod and Logic Cable Pin Assignments Power Supply Fuse Replacement Power Switch/Connector AssemblyFreescale Semiconductor, Inc Power Supply Fuse Replacement MMDS0508 Target Interface Mmds Target Component Configuration GeneralMMDS0508 Definitions, Acronyms and Abbreviations Interfacing Your System and the TargetLoading the MMDS0508 Target Hardware connectionCommunication Configuration Loading MotoSIL TargetCommunication Device Specification MotoSIL Communication ConfigurationDebugger Status Bar for MMDS0508 Menu EntriesData Format Communication Baud Rate CommunicationMemory Configuration Maximum Baud RateShow Protocol Personality .MEM Files 0nnnnVxx.MEM 12 Error Message Signals Emulation Dual-Port RAMMemory Reset Bus TracingMCU Clock Default Target Setup Motorola ESL ParametersComdev Bus Analyzer Introduction to the Bus AnalyzerBaudrate ShowprotUsing the Bus Analyzer WatchpointsTrace Modes Trace BufferTrace window popup menu 15 Bus AnalyzerTrigger Setup 17 Bus Analyzer Trigger SetupSequencer Setup Non-Triggered Modes Continuous All CyclesTriggered Modes/Sequential Event Mode Counted ModesCounted/Sequential Recording Mode Time Tag Clock Setup Clock FrequencyCollecting Data Viewing Collected Data Recording Bus DataTrigger Event View CyclesTextual Display EventsControl Signals Instructions Only DisplayTime Tag Time MeasuringGraphical Display Zoom In or Out22 Trace Zoom Display ShowLocation Add / Remove Items in the Trace WindowScrolling the Display Search for a FrameSearch for Events OK ButtonForward BackwardSearch for a Pattern Previous EventCancel Button Next PatternPrevious Pattern Dumping the Bus analyzer data to a file Dump File31 Analyzer Dump Only Frame Mmds Commands Baud Rate CommandShort Description SyntaxTrigger Commands Set trigger Data RED ORG YEL GRN Examples Disables triggers a and B Bus Analyzer Commands Darm GP B Log trace Open the logging file Sets the 8 Mhz oscillator as the time tag clock source Address SP 8 Set sequencer Display time tag difference VA MODE=MIX INS Graph Target Signal Emulation Commands Reset CommandsOther Commands MEM OSC Protocol Disables the real time memory block Index IDX-84 MMDS0508 Target Interface IDX-85 IDX-86