Freescale Semiconductor MMDS0508 manual Target Cable Connection, Power Connection

Page 15

Freescale Semiconductor, Inc.

Installation

Making Cable Connections

If you need the second logic cable assembly, connect it in the same way to the remaining pod connector of the station module. Make target-system connections as for the first cable.

2.5.3 Target Cable Connection

To connect the MMDS to a target system, you must use a target cable assembly: a target cable and a target head.

NOTE	Press only on the rigid plastic terminators of the cable. Pressing on
	the flexible part of the cable can damage the cable.

Follow these instructions:

1.Make sure that station module power is off; make sure that power is not applied to the target system.

2.Remove the MMDS access panel, for access to the EM.

3.The EM has one or two target connectors, on its right side. Connect the target cable’s emulator terminal to the EM target connectors.

4.Connect the target cable’s head terminator to the appropriate target head adapter.

NOTE	The EM user’s manual should identify the target head adapter
	appropriate for your target system. Make sure that the adapter and the
	target cable mate correctly.

5.Plug the target head adapter into the MCU socket (or surface-mount adapter) of the target system.

6.Replace the access panel. (The target cable must run through the slit in the station-module enclosure.)

2.5.4 Power Connection

The final MMDS connection is line power. The MMDS power switch is the rocker switch on the left side of the station module. Set the power switch to OFF.

Insert the female end of the power cord into the power cord socket. Then plug the other end of the cord into a line-power outlet and set the power switch to ON. The green LED on the front of the station module lights to confirm system power.

MMDS0508 Target Interface

2–15

For More Information: www.freescale.com

Image 15

Contents Freescale Semiconductor, Inc MMDS0508 Target InterfaceHow to Contact Metrowerks Table of Contents Appendix Introduction Mmds FeaturesSystem Components Freescale Semiconductor, Inc System Components MMDS0508 Target Interface Installation M68MMDS0508 Station Module Right Side Factory Test Header J1 Configuring the Platform Board Factory Test Header J1 Port Voltage Control Headers J2-J4Removing the EM Installing the EMMaking Cable Connections Host Computer ConnectionBus State Analyzer Connection Target Cable Connection Power ConnectionMaking Cable Connections MMDS0508 Target Interface RS232 Serial Connector Reset SwitchSerial Connector and Cable Pin Assignments Logic Cables and ConnectorsPod and Logic Cable Pin Assignments Power Switch/Connector Assembly Power Supply Fuse ReplacementFreescale Semiconductor, Inc Power Supply Fuse Replacement MMDS0508 Target Interface Mmds Target Component Configuration GeneralMMDS0508 Interfacing Your System and the Target Definitions, Acronyms and AbbreviationsHardware connection Loading the MMDS0508 TargetLoading MotoSIL Target Communication ConfigurationMotoSIL Communication Configuration Communication Device SpecificationDebugger Status Bar for MMDS0508 Menu EntriesData Format Communication Communication Baud RateMemory Configuration Maximum Baud RateShow Protocol 0nnnnVxx.MEM Personality .MEM Files12 Error Message Signals Emulation Dual-Port RAMMemory Reset Bus TracingMCU Clock Default Target Setup Motorola ESL ParametersComdev Showprot Bus AnalyzerIntroduction to the Bus Analyzer BaudrateTrace Buffer Using the Bus AnalyzerWatchpoints Trace Modes15 Bus Analyzer Trace window popup menu17 Bus Analyzer Trigger Setup Trigger SetupSequencer Setup Continuous All Cycles Non-Triggered ModesCounted Modes Triggered Modes/Sequential Event ModeCounted/Sequential Recording Mode Clock Frequency Time Tag Clock SetupCollecting Data View Cycles Viewing Collected DataRecording Bus Data Trigger EventEvents Textual DisplayTime Measuring Control SignalsInstructions Only Display Time TagZoom In or Out Graphical Display22 Trace Zoom Display Add / Remove Items in the Trace Window ShowLocationSearch for a Frame Scrolling the DisplayBackward Search for EventsOK Button ForwardPrevious Event Search for a PatternCancel Button Next PatternPrevious Pattern Dump File Dumping the Bus analyzer data to a file31 Analyzer Dump Only Frame Syntax Mmds CommandsBaud Rate Command Short DescriptionTrigger Commands Set trigger Data RED ORG YEL GRN Examples Disables triggers a and B Bus Analyzer Commands Darm GP B Log trace Open the logging file Sets the 8 Mhz oscillator as the time tag clock source Address SP 8 Set sequencer Display time tag difference VA MODE=MIX INS Graph Reset Commands Target Signal Emulation CommandsOther Commands MEM OSC Protocol Disables the real time memory block Index IDX-84 MMDS0508 Target Interface IDX-85 IDX-86