Freescale Semiconductor MMDS0508 manual Appendix

Page 4

Freescale Semiconductor, Inc.

Table of Contents

4.3.5	MCU	. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	25
4.3.6	EM .	. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	25

4.4Interfacing Your System and the Target . . . . . . . . . . . . . . . . . . . 25

4.4.1 Hardware Connection . . . . . . . . . . . . . . . . . . . . . . . . . 25

4.5Loading the MMDS0508 Target . . . . . . . . . . . . . . . . . . . . . . 26

4.6Communication Configuration . . . . . . . . . . . . . . . . . . . . . . 27

4.6.1	Communication Device Specification	. . . . . . . . . . . . . . . . . .	28
4.6.2	Data Format	. . . . . . . . . . . . . . . . . . .	29

4.7The Debugger Status Bar for the MMDS . . . . . . . . . . . . . . . . . . 29

4.8MMDS0508 Menu Entries . . . . . . . . . . . . . . . . . . . . . . . . 29

4.8.1Communication Baud Rate . . . . . . . . . . . . . . . . . . . . . . . 30

4.8.2	Memory Configuration	. . . . . . . . . . . . . . . . . . . . . . . .	31
4.8.3	Personality (.MEM) Files	. . . . . . . . . . . . . . . . . . . . . . .	32
4.8.4	Signals Emulation . .	. . . . . . . . . . . . . . . . . . . . . . . .	34
4.8.5	Bus Tracing	. . . . . . . . . . . . . . . . . . . . . . . .	35

4.9Default Target Setup . . . . . . . . . . . . . . . . . . . . . . . . . . 36

4.9.1

Motorola ESL Parameters . . . . . . . . . . . . . . . . . . . . . . . 36

4.10Bus Analyzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

4.10.1 Introduction to the Bus Analyzer . . . . . . . . . . . . . . . . . . . . 37

4.10.2Using the Bus Analyzer . . . . . . . . . . . . . . . . . . . . . . . . 38

4.10.3 Collecting Data . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

4.10.4Viewing Collected Data . . . . . . . . . . . . . . . . . . . . . . . . 47

4.10.5	Scrolling the Display	53
4.10.6	Dumping the Bus analyzer data to a file	57

A	Appendix	59
A.1	MMDS Commands	59
A.1.1	Baud Rate Command	59
A.1.2	Trigger Commands	60
A.1.3	Bus Analyzer Commands	66
A.1.4	Target Signal Emulation Commands	77
A.1.5	Reset Commands	77
A.1.6	Other Commands	78

TOC–4

MMDS0508 Target Interface

For More Information: www.freescale.com

Image 4

Contents MMDS0508 Target Interface Freescale Semiconductor, IncHow to Contact Metrowerks Table of Contents Appendix Mmds Features IntroductionSystem Components Freescale Semiconductor, Inc System Components MMDS0508 Target Interface Installation M68MMDS0508 Station Module Right Side Configuring the Platform Board Factory Test Header J1Port Voltage Control Headers J2-J4 Factory Test Header J1Installing the EM Removing the EMHost Computer Connection Making Cable ConnectionsBus State Analyzer Connection Power Connection Target Cable ConnectionMaking Cable Connections MMDS0508 Target Interface Reset Switch RS232 Serial ConnectorLogic Cables and Connectors Serial Connector and Cable Pin AssignmentsPod and Logic Cable Pin Assignments Power Supply Fuse Replacement Power Switch/Connector AssemblyFreescale Semiconductor, Inc Power Supply Fuse Replacement MMDS0508 Target Interface Mmds Target Component General ConfigurationMMDS0508 Definitions, Acronyms and Abbreviations Interfacing Your System and the TargetLoading the MMDS0508 Target Hardware connectionCommunication Configuration Loading MotoSIL TargetCommunication Device Specification MotoSIL Communication ConfigurationMMDS0508 Menu Entries Debugger Status Bar forData Format Communication Baud Rate CommunicationMaximum Baud Rate Memory ConfigurationShow Protocol Personality .MEM Files 0nnnnVxx.MEM12 Error Message Dual-Port RAM Signals EmulationMemory Bus Tracing ResetMCU Clock Motorola ESL Parameters Default Target SetupComdev Bus Analyzer Introduction to the Bus AnalyzerBaudrate ShowprotUsing the Bus Analyzer WatchpointsTrace Modes Trace BufferTrace window popup menu 15 Bus AnalyzerTrigger Setup 17 Bus Analyzer Trigger SetupSequencer Setup Non-Triggered Modes Continuous All CyclesTriggered Modes/Sequential Event Mode Counted ModesCounted/Sequential Recording Mode Time Tag Clock Setup Clock FrequencyCollecting Data Viewing Collected Data Recording Bus DataTrigger Event View CyclesTextual Display EventsControl Signals Instructions Only DisplayTime Tag Time MeasuringGraphical Display Zoom In or Out22 Trace Zoom Display ShowLocation Add / Remove Items in the Trace WindowScrolling the Display Search for a FrameSearch for Events OK ButtonForward BackwardSearch for a Pattern Previous EventNext Pattern Cancel ButtonPrevious Pattern Dumping the Bus analyzer data to a file Dump File31 Analyzer Dump Only Frame Mmds Commands Baud Rate CommandShort Description SyntaxTrigger Commands Set trigger Data RED ORG YEL GRN Examples Disables triggers a and B Bus Analyzer Commands Darm GP B Log trace Open the logging file Sets the 8 Mhz oscillator as the time tag clock source Address SP 8 Set sequencer Display time tag difference VA MODE=MIX INS Graph Target Signal Emulation Commands Reset CommandsOther Commands MEM OSC Protocol Disables the real time memory block Index IDX-84 MMDS0508 Target Interface IDX-85 IDX-86