Freescale Semiconductor MMDS0508 manual Protocol

Page 81

Freescale Semiconductor, Inc.

Appendix

MMDS Commands

Example:

OSC OSC8MHZ // Use the 8 Mhz internal

emulator clock.

PROTOCOL

A.1.6.10 Short Description

controls Show Protocol functionality.

A.1.6.11 Syntax

PROTOCOL [ON OFF]

ON: Reports commands and responses in the command line window (default value for this command).

OFF: Does not report commands or responses in the command line window; does not log commands or responses in the log file.

A.1.6.12 Description

The PROTOCOL command controls reporting commands and responses in the command line window. Entering this command without a parameter value has the same effect as entering the command with the parameter value ON.

RTMEM

A.1.6.13 Short Description

configures real time memory.

A.1.6.14 Syntax

RTMEM address [;E;D]

address: base address of a real time memory block (default is 0).

;E: Enables the real time memory block (the default for this command).

MMDS0508 Target Interface

A–81

For More Information: www.freescale.com

Image 81

Contents Freescale Semiconductor, Inc MMDS0508 Target InterfaceHow to Contact Metrowerks Table of Contents Appendix Introduction Mmds FeaturesSystem Components Freescale Semiconductor, Inc System Components MMDS0508 Target Interface Installation M68MMDS0508 Station Module Right Side Factory Test Header J1 Configuring the Platform BoardFactory Test Header J1 Port Voltage Control Headers J2-J4Removing the EM Installing the EMMaking Cable Connections Host Computer ConnectionBus State Analyzer Connection Target Cable Connection Power ConnectionMaking Cable Connections MMDS0508 Target Interface RS232 Serial Connector Reset SwitchSerial Connector and Cable Pin Assignments Logic Cables and ConnectorsPod and Logic Cable Pin Assignments Power Switch/Connector Assembly Power Supply Fuse ReplacementFreescale Semiconductor, Inc Power Supply Fuse Replacement MMDS0508 Target Interface Mmds Target Component Configuration GeneralMMDS0508 Interfacing Your System and the Target Definitions, Acronyms and AbbreviationsHardware connection Loading the MMDS0508 TargetLoading MotoSIL Target Communication ConfigurationMotoSIL Communication Configuration Communication Device SpecificationDebugger Status Bar for MMDS0508 Menu EntriesData Format Communication Communication Baud RateMemory Configuration Maximum Baud RateShow Protocol 0nnnnVxx.MEM Personality .MEM Files12 Error Message Signals Emulation Dual-Port RAMMemory Reset Bus TracingMCU Clock Default Target Setup Motorola ESL ParametersComdev Introduction to the Bus Analyzer Bus AnalyzerBaudrate ShowprotWatchpoints Using the Bus AnalyzerTrace Modes Trace Buffer15 Bus Analyzer Trace window popup menu17 Bus Analyzer Trigger Setup Trigger SetupSequencer Setup Continuous All Cycles Non-Triggered ModesCounted Modes Triggered Modes/Sequential Event ModeCounted/Sequential Recording Mode Clock Frequency Time Tag Clock SetupCollecting Data Recording Bus Data Viewing Collected DataTrigger Event View CyclesEvents Textual DisplayInstructions Only Display Control SignalsTime Tag Time MeasuringZoom In or Out Graphical Display22 Trace Zoom Display Add / Remove Items in the Trace Window ShowLocationSearch for a Frame Scrolling the DisplayOK Button Search for EventsForward BackwardPrevious Event Search for a PatternCancel Button Next PatternPrevious Pattern Dump File Dumping the Bus analyzer data to a file31 Analyzer Dump Only Frame Baud Rate Command Mmds CommandsShort Description SyntaxTrigger Commands Set trigger Data RED ORG YEL GRN Examples Disables triggers a and B Bus Analyzer Commands Darm GP B Log trace Open the logging file Sets the 8 Mhz oscillator as the time tag clock source Address SP 8 Set sequencer Display time tag difference VA MODE=MIX INS Graph Reset Commands Target Signal Emulation CommandsOther Commands MEM OSC Protocol Disables the real time memory block Index IDX-84 MMDS0508 Target Interface IDX-85 IDX-86