Cypress CY7C1513V18 manual Switching Characteristics, Parameter Min Max, High, Low, Rps, Wps

CY7C1511V18, CY7C1526V18

CY7C1513V18, CY7C1515V18

Switching Characteristics

Over the Operating Range [22, 23]

Cypress

Consortium

Description

300 MHz

278 MHz

250 MHz

200 MHz

167 MHz

Unit

Parameter

Parameter

Min

Max

Min

Max

Min

Max

Min

Max

Min

Max

t

POWER

V (Typical) to the First Access [24]

1

1

1

1

1

ms

DD

tCYC

tKHKH

K Clock and C Clock Cycle Time

3.3

8.4

3.6

8.4

4.0

8.4

5.0

8.4

6.0

8.4

ns

tKH

tKHKL

1.32

–

1.4

–

1.6

–

2.0

–

2.4

–

ns

Input Clock (K/K;

C/C) HIGH

tKL

tKLKH

1.32

–

1.4

–

1.6

–

2.0

–

2.4

–

ns

Input Clock (K/K;

C/C) LOW

tKHKH

tKHKH

K Clock Rise to

Clock Rise and C

1.49

–

1.6

–

1.8

–

2.2

–

2.7

–

ns

K

to C Rise (rising edge to rising edge)

tKHCH

tKHCH

0

1.45

0

1.55

0

1.8

0

2.2

0

2.7

ns

K/K

Clock Rise to C/C Clock Rise

(rising edge to rising edge)

Setup Times

tSA

tAVKH

Address Setup to K Clock Rise

0.4

–

0.4

–

0.5

–

0.6

–

0.7

–

ns

tSC

tIVKH

Control Setup to K Clock Rise

0.4

–

0.4

–

0.5

–

0.6

–

0.7

–

ns

(RPS, WPS)

tSCDDR

tIVKH

Double Data Rate Control Setup to

0.3

–

0.3

–

0.35

–

0.4

–

0.5

–

ns

Clock (K/K) Rise

(BWS0, BWS1,

BWS

2,

BWS

3)

tSD [25]

tDVKH

D

Rise

0.3

–

0.3

–

0.35

–

0.4

–

0.5

–

ns

Setup to Clock (K/K)

[X:0]

Hold Times

tHA

tKHAX

Address Hold after K Clock Rise

0.4

–

0.4

–

0.5

–

0.6

–

0.7

–

ns

tHC

tKHIX

Control Hold after K Clock Rise

0.4

–

0.4

–

0.5

–

0.6

–

0.7

–

ns

(RPS, WPS)

tHCDDR

tKHIX

Double Data Rate Control Hold after

0.3

–

0.3

–

0.35

–

0.4

–

0.5

–

ns

Clock (K/K) Rise

(BWS0, BWS1,

BWS

2,

BWS

3)

tHD

tKHDX

D

Rise

0.3

–

0.3

–

0.35

–

0.4

–

0.5

–

ns

Hold after Clock (K/K)

[X:0]

Notes

23.When a part with a maximum frequency above 167 MHz is operating at a lower clock frequency, it requires the input timings of the frequency range in which it is being operated and outputs data with the output timings of that frequency range.

24.This part has a voltage regulator internally; tPOWER is the time that the power must be supplied above VDD minimum initially before a read or write operation can be initiated.

25.For D0 data signal on CY7C1526V18 device, tSD is 0.5 ns for 200 MHz, 250 MHz, 278 MHz and 300 MHz frequencies.

Document Number: 38-05363 Rev. *F Page 24 of 32

[+] Feedback