Datacard Group RL90, RP90 manual Load laminate, Tips Handling patch, Or topcoat material

Page 17

Load Supplies

Load laminate

 

 

Tips: Handling patch

1 Open the laminator door by

 

pulling the top of the door

or topcoat material

 

 

toward you.

 

After powering on the

 

2

Press the laminator cartridge

 

laminator, the patch or

 

eject button and remove the

 

topcoat material must be

 

laminator cartridge carefully.

 

initialized. Press the

 

The material must be tight

 

laminator’s RESET/K and

 

when removing the cartridge.

 

then the ENTER keys to

3

Place the roll of

 

initialize the material.

 

 

material and

 

 

 

The inside of the laminator

 

empty take-up

 

spool side by side

 

contains hot surfaces. Use

 

on a clean

 

care when working in these

 

surface.

 

areas.

4

Remove the label from the

 

 

Keep unused laminating

 

patch or topcoat material and

 

use it to secure the free end of

 

material in the original

 

 

 

the material to the empty take-

 

package.

 

 

 

up spool, making sure the

Don't place material on a

 

edges are even.

5

Load the new roll of material

 

dusty or dirty surface — dirt

 

 

on the cartridge:

 

can affect card quality.

 

 

 

a Put the full roll of material

 

 

 

During the laminating

 

on the supply spindle.

 

process, do not turn the

 

b Put the empty take-up

 

power switch off, open the

 

spool on the take-up

 

laminator door, or unplug the

 

spindle.

 

laminator.

 

c Align the material along

 

See “Laminator material” on

 

the four metal guides as

 

shown on the cartridge

 

page 68 for more information

 

label.

 

about laminating material.

 

d Wind two or three

 

 

 

rotations of film onto the

 

 

 

take-up spool. Take up

 

 

 

slack between the spools

 

 

 

by turning the supply knob

 

 

 

clockwise. If slack cannot

 

 

 

be removed, check that

 

 

 

the supply and take-up

 

 

 

spools are firmly seated on

 

 

 

the spindles.

 

 

6 Replace the loaded laminator

 

 

 

cartridge in the laminator until

 

 

 

it clicks into position.

 

 

7 Close the laminator door.

RP90 Plus E and RL90 User Guide

 

11

Image 17
Contents User Guide Regulatory compliance Contents Messages RP90 Plus E and RL90 User Guide Liability statement SafetySafe environment Safe human interfaceWho to call for assistance Introduction1About this manual Outside of the printer About the PrinterInside of the printer Back of the printer Parts of the laminator About the laminatorAbout the laminator RP90 Plus E and RL90 User Guide Using the printer Load cards Load SuppliesTips Handling cards See Supplies on page 67 for specific card informationTips Handling ink ribbon Load ink ribbonTips Handling retransfer film Load retransfer filmTips Handling patch Load laminateOr topcoat material See Laminator material onCheck the PC connection Power onOptional laminator connection LCD sequence on laminator startup Power on the laminatorTips for laminator power LCD sequence on printer startup Power on the printerTips for printer power Initialize the ink ribbon Prepare to print cardsSet the retransfer film type Tips Ink ribbonInitialize the retransfer film Printing cards Print cards using ID softwareTips Printing Print from a PC applicationPrinting cards RP90 Plus E and RL90 User Guide Viewing and changing Printer settings Printing Preferences Setup tabEncode tab Printing Properties Tips Card cleaning rollerTips for Success Status MonitorOpen the Status Monitor Printer Status tab Close the Status MonitorSee Status monitor messages on Printer Setting tabIcon Status Icon Color Meaning Bend Remedy tab Retransfer tabDisplay Reasons for ink recognition error and the solutions Media Setting tabPrinter Select tab Property tabSee Hopper jam on page 52 to remove Status monitor messagesOthers tab See Retransfer section jam on page 54 to See Turnover jam on page 53 to removeMending broken ink ribbon or retransfer Film on Correctly see Load retransfer film onPower on the printer on page 15 Initialize the ink ribbon on Ink ribbon onPrinter LCD panel on Using the LCD menusAbout the Printer LCD panel Heat roller on page 45 or Cleaning the magnetic Using the Printer LCD panelMagnetic stripe cards. See Cleaning the card feed rollers Menu Display Menu Display USB See Preparing the printer and laminator for transport Menu About the Laminator LCD panelLaminator on page 49 for more information Using the Laminator LCD panelTaking care of your printer Cleaning the card cleaning rollers Cleaning the printerCard feed roller Load cards onPower on the printer. See Power on the printer on Cleaning the card feed rollers and heat rollerTips Cleaning card feed and heat rollers Tips -Magnetic head cleaning card Cleaning the magnetic headTips Thermal head Cleaning the thermal headCleaning printer fan filters Preparing the printer and laminator for transport Tips Laminator cleaning card Cleaning the laminatorRun a laminator cleaning card Laminator fan filter Cleaning the laminator cartridgePrinter roller layout Messages Error recoveryHopper jam Printer error recoveryTips Turnover jam Turnover jamTips Retransfer jam Retransfer section jamRibbon on page 16 or Initialize the retransfer film on Mending broken ink ribbon or retransfer filmBend remedy Bend remedy printer settingsTips -Bend Remedy Remedy tab onTo set the laminator Card Fan Bend remedy laminator settingsPrinter LCD messages See Cleaning the card feed rollers and heatSee Hopper jam on See Turnover jam onMending broken ink ribbon or retransfer film As described in Operating environment on See Cleaning the card cleaning rollers onDescribed in Retransfer section jam on Tips Laminator card jam Laminator error recoveryCard jam Align the end of the supply material with Change the left-to-right position Patch positionLaminator LCD messages LCD Message Possible Cause Solution Supplies6 Cards Ink ribbon, retransfer film, and laminator materialInk ribbon Retransfer filmCard material Cleaning suppliesCard size RP90 Plus E and RL90 User Guide Site requirements Tips Site selection Site guidelinesOperating environment Storage Environment for supplies Ventilation clearancePrinter specifications Laminator specifications RP90 Plus E and RL90 User Guide Inline Encoding on Character Code Table on Magnetic Stripe EncodingTip for success Inline EncodingExample DEL Character Code TableCharacter Code Table RP90 Plus E and RL90 User Guide Compliance FCC Regulatory compliance Design and information contained in these June