Datacard Group RP90, RL90 manual See Preparing the printer and laminator for transport

Page 46

 

 

Using the LCD menus

 

 

 

 

 

 

Menu Display

Settings

Function

 

 

 

 

Subnet Mask

The default Subnet Mask of the printer is 255.255.255.0. If

 

 

you do not use DHCP, ask your network administrator for the

 

 

Subnet mask.

 

 

 

 

Gateway

The default Gateway of the printer is 192.168.0.1. If you do

 

 

not use DHCP, ask your network administrator for the Subnet

 

 

mask.

 

 

 

 

Session TimeOut

Set how many minutes to wait without using the printer to stop

 

OFF or up to 60 minutes

the network session between the PC and printer.

 

 

 

 

MAC Address

The MAC Address is unique to each printer. The MAC

 

 

Address is displayed and cannot be changed.

 

 

 

 

IPSec Mode

Set the Internet Protocol (IP) Security mode to ON or to OFF.

 

ON

After setting up security using a PC and USB connection, this

 

OFF

setting cannot be changed.

 

 

 

 

IPSec Type

Set the type of IP Security. Choose from the following:

 

 

• Not Setting, no IP Security.

 

 

• Preshared, using a preshared key for encryption.

 

 

• Certificate, using a public key certificate for encryption.

 

 

After setting up security using a PC and USB connection, this

 

 

setting cannot be changed.

 

 

 

HR Control

ON

Set whether to lower the temperature of the retransfer heat

 

OFF

roller after 30 minutes of no printing. The roller returns to

 

 

operating temperature when the next card is printed.

 

 

Setting HR Control to ON can add to the useful life of the

 

 

retransfer heat roller.

 

 

 

Download

 

To prepare the printer for a firmware download, press the

 

 

ENTER key. The firmware must be downloaded from a USB-

 

 

connected PC with the driver and Status Monitor installed.

 

 

See “Others tab” on page 31 for the Status Monitor page.

 

 

DO NOT power off the printer while the firmware is being

 

 

downloaded.

 

 

 

Transport Mode

Set transport mode

Set the Transport Mode when moving or shipping the printer.

 

 

Press the ENTER key to use the transport mode. “Please,

 

 

power off” is displayed on the LCD panel. The transport mode

 

 

is cancelled when the printer is powered back on.

 

 

See “Preparing the printer and laminator for transport”

 

 

on page 48 for information on preparing the printer for

 

 

transporting it.

 

 

 

40

RP90 Plus E and RL90 User Guide

Page 45 Page 47
Image 46
Page 45 Page 47
Contents User Guide Regulatory compliance Contents Messages RP90 Plus E and RL90 User Guide Safe environment SafetyLiability statement Safe human interfaceAbout this manual Introduction1Who to call for assistance About the Printer Outside of the printerInside of the printer Back of the printer About the laminator Parts of the laminatorAbout the laminator RP90 Plus E and RL90 User Guide Using the printer Tips Handling cards Load SuppliesLoad cards See Supplies on page 67 for specific card informationLoad ink ribbon Tips Handling ink ribbonLoad retransfer film Tips Handling retransfer filmOr topcoat material Load laminateTips Handling patch See Laminator material onPower on Check the PC connectionOptional laminator connection Tips for laminator power Power on the laminatorLCD sequence on laminator startup Tips for printer power Power on the printerLCD sequence on printer startup Set the retransfer film type Prepare to print cardsInitialize the ink ribbon Tips Ink ribbonInitialize the retransfer film Print cards using ID software Printing cardsPrint from a PC application Tips PrintingPrinting cards RP90 Plus E and RL90 User Guide Viewing and changing Printer settings Setup tab Printing PreferencesEncode tab Tips Card cleaning roller Printing PropertiesOpen the Status Monitor Status MonitorTips for Success Close the Status Monitor Printer Status tabIcon Status Icon Color Meaning Printer Setting tabSee Status monitor messages on Retransfer tab Bend Remedy tabMedia Setting tab Display Reasons for ink recognition error and the solutionsProperty tab Printer Select tabOthers tab Status monitor messagesSee Hopper jam on page 52 to remove Mending broken ink ribbon or retransfer Film on See Turnover jam on page 53 to removeSee Retransfer section jam on page 54 to Correctly see Load retransfer film onPower on the printer on page 15 Ink ribbon on Initialize the ink ribbon onAbout the Printer LCD panel Using the LCD menusPrinter LCD panel on Magnetic stripe cards. See Cleaning the card feed rollers Using the Printer LCD panelHeat roller on page 45 or Cleaning the magnetic Menu Display Menu Display USB See Preparing the printer and laminator for transport About the Laminator LCD panel MenuUsing the Laminator LCD panel Laminator on page 49 for more informationTaking care of your printer Card feed roller Cleaning the printerCleaning the card cleaning rollers Load cards onTips Cleaning card feed and heat rollers Cleaning the card feed rollers and heat rollerPower on the printer. See Power on the printer on Cleaning the magnetic head Tips -Magnetic head cleaning cardCleaning printer fan filters Cleaning the thermal headTips Thermal head Preparing the printer and laminator for transport Run a laminator cleaning card Cleaning the laminatorTips Laminator cleaning card Cleaning the laminator cartridge Laminator fan filterMessages Error recovery Printer roller layoutPrinter error recovery Hopper jamTurnover jam Tips Turnover jamRetransfer section jam Tips Retransfer jamMending broken ink ribbon or retransfer film Ribbon on page 16 or Initialize the retransfer film onTips -Bend Remedy Bend remedy printer settingsBend remedy Remedy tab onBend remedy laminator settings To set the laminator Card FanSee Hopper jam on See Cleaning the card feed rollers and heatPrinter LCD messages See Turnover jam onMending broken ink ribbon or retransfer film See Cleaning the card cleaning rollers on As described in Operating environment onDescribed in Retransfer section jam on Card jam Laminator error recoveryTips Laminator card jam Align the end of the supply material with Patch position Change the left-to-right positionLaminator LCD messages LCD Message Possible Cause Solution Supplies6 Ink ribbon Ink ribbon, retransfer film, and laminator materialCards Retransfer filmCard size Cleaning suppliesCard material RP90 Plus E and RL90 User Guide Site requirements Operating environment Site guidelinesTips Site selection Ventilation clearance Storage Environment for suppliesPrinter specifications Laminator specifications RP90 Plus E and RL90 User Guide Magnetic Stripe Encoding Inline Encoding on Character Code Table onExample Inline EncodingTip for success Character Code Table DELCharacter Code Table RP90 Plus E and RL90 User Guide Compliance FCC Regulatory compliance Design and information contained in these June
Top Page Image Contents