Datacard Group RL90, RP90 manual Mending broken ink ribbon or retransfer film

Page 61

Printer error recovery

Mending broken ink ribbon or retransfer film

If the ink ribbon or retransfer film breaks, “Media Broken” is displayed on the LCD panel. Broken ink ribbon is shown in the following example; repairing broken retransfer film uses the same steps.

1Slide the door latch to the right and open the printer door.

2Remove the cartridge by pressing the cartridge eject button.

3Trim the ends of the broken

portions evenly.

4Do not remove the used ink ribbon or film from the take-up

spool.

5 Align the ends of the broken media evenly and apply tape to secure.

6 Turn the take-up spool clockwise until the mended portion is wound onto the spool two or three turns.

7Reinstall the cartridge into the printer until it clicks into

position.

8 Close printer door.

9Initialize the ribbon or film as described in “Initialize the ink

ribbon” on page 16 or “Initialize the retransfer film” on page 17.

RP90 Plus E and RL90 User Guide

55

Image 61

Contents User Guide Regulatory compliance Contents Messages RP90 Plus E and RL90 User Guide Liability statement SafetySafe environment Safe human interfaceAbout this manual Introduction1Who to call for assistance Outside of the printer About the PrinterInside of the printer Back of the printer Parts of the laminator About the laminatorAbout the laminator RP90 Plus E and RL90 User Guide Using the printer Load cards Load SuppliesTips Handling cards See Supplies on page 67 for specific card informationTips Handling ink ribbon Load ink ribbonTips Handling retransfer film Load retransfer filmTips Handling patch Load laminateOr topcoat material See Laminator material onCheck the PC connection Power onOptional laminator connection Tips for laminator power Power on the laminatorLCD sequence on laminator startup Tips for printer power Power on the printerLCD sequence on printer startup Initialize the ink ribbon Prepare to print cardsSet the retransfer film type Tips Ink ribbonInitialize the retransfer film Printing cards Print cards using ID softwareTips Printing Print from a PC applicationPrinting cards RP90 Plus E and RL90 User Guide Viewing and changing Printer settings Printing Preferences Setup tabEncode tab Printing Properties Tips Card cleaning rollerOpen the Status Monitor Status MonitorTips for Success Printer Status tab Close the Status MonitorIcon Status Icon Color Meaning Printer Setting tabSee Status monitor messages on Bend Remedy tab Retransfer tabDisplay Reasons for ink recognition error and the solutions Media Setting tabPrinter Select tab Property tabOthers tab Status monitor messagesSee Hopper jam on page 52 to remove See Retransfer section jam on page 54 to See Turnover jam on page 53 to removeMending broken ink ribbon or retransfer Film on Correctly see Load retransfer film onPower on the printer on page 15 Initialize the ink ribbon on Ink ribbon onAbout the Printer LCD panel Using the LCD menusPrinter LCD panel on Magnetic stripe cards. See Cleaning the card feed rollers Using the Printer LCD panelHeat roller on page 45 or Cleaning the magnetic Menu Display Menu Display USB See Preparing the printer and laminator for transport Menu About the Laminator LCD panelLaminator on page 49 for more information Using the Laminator LCD panelTaking care of your printer Cleaning the card cleaning rollers Cleaning the printerCard feed roller Load cards onTips Cleaning card feed and heat rollers Cleaning the card feed rollers and heat rollerPower on the printer. See Power on the printer on Tips -Magnetic head cleaning card Cleaning the magnetic headCleaning printer fan filters Cleaning the thermal headTips Thermal head Preparing the printer and laminator for transport Run a laminator cleaning card Cleaning the laminatorTips Laminator cleaning card Laminator fan filter Cleaning the laminator cartridgePrinter roller layout Messages Error recoveryHopper jam Printer error recoveryTips Turnover jam Turnover jamTips Retransfer jam Retransfer section jamRibbon on page 16 or Initialize the retransfer film on Mending broken ink ribbon or retransfer filmBend remedy Bend remedy printer settingsTips -Bend Remedy Remedy tab onTo set the laminator Card Fan Bend remedy laminator settingsPrinter LCD messages See Cleaning the card feed rollers and heatSee Hopper jam on See Turnover jam onMending broken ink ribbon or retransfer film As described in Operating environment on See Cleaning the card cleaning rollers onDescribed in Retransfer section jam on Card jam Laminator error recoveryTips Laminator card jam Align the end of the supply material with Change the left-to-right position Patch positionLaminator LCD messages LCD Message Possible Cause Solution Supplies6 Cards Ink ribbon, retransfer film, and laminator materialInk ribbon Retransfer filmCard size Cleaning suppliesCard material RP90 Plus E and RL90 User Guide Site requirements Operating environment Site guidelinesTips Site selection Storage Environment for supplies Ventilation clearancePrinter specifications Laminator specifications RP90 Plus E and RL90 User Guide Inline Encoding on Character Code Table on Magnetic Stripe EncodingExample Inline EncodingTip for success DEL Character Code TableCharacter Code Table RP90 Plus E and RL90 User Guide Compliance FCC Regulatory compliance Design and information contained in these June