Datacard Group RP90, RL90 manual Laminator error recovery, Card jam, Tips Laminator card jam

Page 68

Laminator error recovery

Laminator error recovery

Card jam

Tips – Laminator card jam

•Make sure that the card stacker is not blocking the card discharge slot.

•The area around the heat roller is very hot. Be careful when removing a jammed card.

The laminator LCD panel displays the error.

The laminator LCD panel displays the location of the card jam: Card Jam (In), Card Jam (Middle), or Card Jam (Out). Use the following steps to remove card jams.

1Open the laminator door by

pulling the top of the door toward you.

2 Turn the take-up knob clockwise to remove slack in the laminator material.

3 Press the laminator cartridge eject button and remove the laminator cartridge. The cartridge may be difficult to remove; pull firmly, but do not force. If cartridge cannot be removed, call for service.

4Use a coin to turn the jog dial, which will move the card. The

jog dial can be turned clockwise or counterclockwise depending on the location of the card.

5 Remove the jammed card. The area around the heat roller is very hot. Be careful when removing a jammed card.

62	RP90 Plus E and RL90 User Guide

Image 68

Contents User Guide Regulatory compliance Contents Messages RP90 Plus E and RL90 User Guide Safety Liability statementSafe environment Safe human interfaceWho to call for assistance Introduction1About this manual About the Printer Outside of the printerInside of the printer Back of the printer About the laminator Parts of the laminatorAbout the laminator RP90 Plus E and RL90 User Guide Using the printer Load Supplies Load cardsTips Handling cards See Supplies on page 67 for specific card informationLoad ink ribbon Tips Handling ink ribbonLoad retransfer film Tips Handling retransfer filmLoad laminate Tips Handling patchOr topcoat material See Laminator material onPower on Check the PC connectionOptional laminator connection LCD sequence on laminator startup Power on the laminatorTips for laminator power LCD sequence on printer startup Power on the printerTips for printer power Prepare to print cards Initialize the ink ribbonSet the retransfer film type Tips Ink ribbonInitialize the retransfer film Print cards using ID software Printing cardsPrint from a PC application Tips PrintingPrinting cards RP90 Plus E and RL90 User Guide Viewing and changing Printer settings Setup tab Printing PreferencesEncode tab Tips Card cleaning roller Printing PropertiesTips for Success Status MonitorOpen the Status Monitor Close the Status Monitor Printer Status tabSee Status monitor messages on Printer Setting tabIcon Status Icon Color Meaning Retransfer tab Bend Remedy tabMedia Setting tab Display Reasons for ink recognition error and the solutionsProperty tab Printer Select tabSee Hopper jam on page 52 to remove Status monitor messagesOthers tab See Turnover jam on page 53 to remove See Retransfer section jam on page 54 toMending broken ink ribbon or retransfer Film on Correctly see Load retransfer film onPower on the printer on page 15 Ink ribbon on Initialize the ink ribbon onPrinter LCD panel on Using the LCD menusAbout the Printer LCD panel Heat roller on page 45 or Cleaning the magnetic Using the Printer LCD panelMagnetic stripe cards. See Cleaning the card feed rollers Menu Display Menu Display USB See Preparing the printer and laminator for transport About the Laminator LCD panel MenuUsing the Laminator LCD panel Laminator on page 49 for more informationTaking care of your printer Cleaning the printer Cleaning the card cleaning rollersCard feed roller Load cards onPower on the printer. See Power on the printer on Cleaning the card feed rollers and heat rollerTips Cleaning card feed and heat rollers Cleaning the magnetic head Tips -Magnetic head cleaning cardTips Thermal head Cleaning the thermal headCleaning printer fan filters Preparing the printer and laminator for transport Tips Laminator cleaning card Cleaning the laminatorRun a laminator cleaning card Cleaning the laminator cartridge Laminator fan filterMessages Error recovery Printer roller layoutPrinter error recovery Hopper jamTurnover jam Tips Turnover jamRetransfer section jam Tips Retransfer jamMending broken ink ribbon or retransfer film Ribbon on page 16 or Initialize the retransfer film onBend remedy printer settings Bend remedyTips -Bend Remedy Remedy tab onBend remedy laminator settings To set the laminator Card FanSee Cleaning the card feed rollers and heat Printer LCD messagesSee Hopper jam on See Turnover jam onMending broken ink ribbon or retransfer film See Cleaning the card cleaning rollers on As described in Operating environment onDescribed in Retransfer section jam on Tips Laminator card jam Laminator error recoveryCard jam Align the end of the supply material with Patch position Change the left-to-right positionLaminator LCD messages LCD Message Possible Cause Solution Supplies6 Ink ribbon, retransfer film, and laminator material CardsInk ribbon Retransfer filmCard material Cleaning suppliesCard size RP90 Plus E and RL90 User Guide Site requirements Tips Site selection Site guidelinesOperating environment Ventilation clearance Storage Environment for suppliesPrinter specifications Laminator specifications RP90 Plus E and RL90 User Guide Magnetic Stripe Encoding Inline Encoding on Character Code Table onTip for success Inline EncodingExample Character Code Table DELCharacter Code Table RP90 Plus E and RL90 User Guide Compliance FCC Regulatory compliance Design and information contained in these June