Datacard Group RL90, RP90 manual Menu Display

Page 43

Using the LCD menus

Menu Display

Ink

Retransfer

Standby

Buzzer

Power Saving

Bend Remedy

Settings

Ink Type

YMCK: 0

YMCKPO: 2

YMCKK: 4

Black level

Black mode

SP - Ink1 Level

SP - Ink2 Level

Media type: 750 1000

Temp Level

Speed (front)

Speed (back)

MG Print (JIS)

Front Wait

Back Wait

ON or OFF

OFF or up to 60 minutes

Temp Level

Speed

Cooling time

Function

Displays the type of ink ribbon that is loaded in the printer. Datacard supports YMCK and YMCKK ink ribbons. (The printer detects the type of ink ribbon; it cannot be set.) See your dealer regarding support for YMCKPO ink ribbon.

Choose from seven gradations from -3 (lighter) to +5 (darker).

Choose Standard or Fine. Change to Fine if thin lines or small black text is blurred (printing speed is slower).

Use SP - Ink1 and Ink2 levels to set the darkness level of special inks that will be available in the future.

See SP -Ink1 Level above.

Datacard retransfer ribbon is available in 1000 frames per roll.

Set the retransfer roller temperature. Set from -3 (lower) to +2 (higher).

Set the retransfer speed for the front of the card. Set from -10 (slower) to +2 (faster). Initialize the retransfer film after making changes. See “Initialize the retransfer film” on page 17.

Set the retransfer speed for the back of the card. Set from -10 (slower) to +2 (faster). Initialize the retransfer film after making changes. See “Initialize the retransfer film” on page 17.

Select ON or OFF.

When printing both sides of a card and using an optional smart card (IC) unit, specifies whether to wait after the front side or the back side of the card.

Use to turn the electronic beep sound ON or OFF. The sound can indicate an error, when fewer than 20 cards remain in the card hopper, or to confirm a menu selection.

The printer enters power save mode after a specified period of inactivity. Choose from OFF or select from 5 to 60 minutes in 5 to15 minute increments. “Sleeping” appears on the LCD display. To cancel power save mode, press RESET and then the ENTER key. The printer uses one set of supplies.

Choose from -5 (lower) to 0 (higher) or OFF to set the bend remedy roller temperature. See “Bend remedy” on page 56 for more information.

Choose from -2 (slower) to +2 (faster) to set the bend remedy speed. See “Bend remedy” on page 56 for more information.

Set the cooling time from 0 (None) to 15 seconds.

RP90 Plus E and RL90 User Guide

37

Page 42 Page 44
Image 43
Page 42 Page 44
Contents User Guide Regulatory compliance Contents Messages RP90 Plus E and RL90 User Guide Safe human interface SafetyLiability statement Safe environmentAbout this manual Introduction1Who to call for assistance Outside of the printer About the PrinterInside of the printer Back of the printer Parts of the laminator About the laminatorAbout the laminator RP90 Plus E and RL90 User Guide Using the printer See Supplies on page 67 for specific card information Load SuppliesLoad cards Tips Handling cardsTips Handling ink ribbon Load ink ribbonTips Handling retransfer film Load retransfer filmSee Laminator material on Load laminateTips Handling patch Or topcoat materialCheck the PC connection Power onOptional laminator connection Tips for laminator power Power on the laminatorLCD sequence on laminator startup Tips for printer power Power on the printerLCD sequence on printer startup Tips Ink ribbon Prepare to print cardsInitialize the ink ribbon Set the retransfer film typeInitialize the retransfer film Printing cards Print cards using ID softwareTips Printing Print from a PC applicationPrinting cards RP90 Plus E and RL90 User Guide Viewing and changing Printer settings Printing Preferences Setup tabEncode tab Printing Properties Tips Card cleaning rollerOpen the Status Monitor Status MonitorTips for Success Printer Status tab Close the Status MonitorIcon Status Icon Color Meaning Printer Setting tabSee Status monitor messages on Bend Remedy tab Retransfer tabDisplay Reasons for ink recognition error and the solutions Media Setting tabPrinter Select tab Property tabOthers tab Status monitor messagesSee Hopper jam on page 52 to remove Correctly see Load retransfer film on See Turnover jam on page 53 to removeSee Retransfer section jam on page 54 to Mending broken ink ribbon or retransfer Film onPower on the printer on page 15 Initialize the ink ribbon on Ink ribbon onAbout the Printer LCD panel Using the LCD menusPrinter LCD panel on Magnetic stripe cards. See Cleaning the card feed rollers Using the Printer LCD panelHeat roller on page 45 or Cleaning the magnetic Menu Display Menu Display USB See Preparing the printer and laminator for transport Menu About the Laminator LCD panelLaminator on page 49 for more information Using the Laminator LCD panelTaking care of your printer Load cards on Cleaning the printerCleaning the card cleaning rollers Card feed rollerTips Cleaning card feed and heat rollers Cleaning the card feed rollers and heat rollerPower on the printer. See Power on the printer on Tips -Magnetic head cleaning card Cleaning the magnetic headCleaning printer fan filters Cleaning the thermal headTips Thermal head Preparing the printer and laminator for transport Run a laminator cleaning card Cleaning the laminatorTips Laminator cleaning card Laminator fan filter Cleaning the laminator cartridgePrinter roller layout Messages Error recoveryHopper jam Printer error recoveryTips Turnover jam Turnover jamTips Retransfer jam Retransfer section jamRibbon on page 16 or Initialize the retransfer film on Mending broken ink ribbon or retransfer filmRemedy tab on Bend remedy printer settingsBend remedy Tips -Bend RemedyTo set the laminator Card Fan Bend remedy laminator settingsSee Turnover jam on See Cleaning the card feed rollers and heatPrinter LCD messages See Hopper jam onMending broken ink ribbon or retransfer film As described in Operating environment on See Cleaning the card cleaning rollers onDescribed in Retransfer section jam on Card jam Laminator error recoveryTips Laminator card jam Align the end of the supply material with Change the left-to-right position Patch positionLaminator LCD messages LCD Message Possible Cause Solution Supplies6 Retransfer film Ink ribbon, retransfer film, and laminator materialCards Ink ribbonCard size Cleaning suppliesCard material RP90 Plus E and RL90 User Guide Site requirements Operating environment Site guidelinesTips Site selection Storage Environment for supplies Ventilation clearancePrinter specifications Laminator specifications RP90 Plus E and RL90 User Guide Inline Encoding on Character Code Table on Magnetic Stripe EncodingExample Inline EncodingTip for success DEL Character Code TableCharacter Code Table RP90 Plus E and RL90 User Guide Compliance FCC Regulatory compliance Design and information contained in these June
Top Page Image Contents