Datacard Group RL90, RP90 manual Laminator LCD messages

Page 71

 

 

Laminator error recovery

 

 

 

Laminator LCD messages

 

 

 

 

LCD Message

Possible Cause

Solution

 

 

 

Please Power OFF

To initialize this unit, the

Turn the laminator’s power switch off, and then back

 

power must be switched

on to initialize the laminator.

 

off once.

 

 

 

 

Please Reset

Displayed when Reset is

Press the RESET/K and then the ENTER key to

 

necessary after changing

initialize the laminator.

 

the settings.

 

 

 

 

Please check inside

The power was switched

Remove the laminator cartridge and check for a card

 

off during lamination.

inside the machine. If there is a card in the machine,

 

 

remove it.

 

 

Press the RESET/K and then the ENTER key to

 

 

initialize the laminator.

 

 

 

Card Jam (in)

There is a card jam in the

Check that the laminator is properly connected to the

 

entrance area.

printer as described in “Optional laminator

 

 

connection” on page 13.

 

 

See “Card jam” on page 62 to clear the jam.

 

 

 

Card Jam (middle)

There is a card jam in the

The laminating temperature is too high or the speed is

 

center of the card path.

too slow. Set the temperature or speed as described in

 

 

“Using the Laminator LCD panel” on page 42.

 

 

See “Card jam” on page 62 to clear the jam.

 

 

 

Card Jam (out)

There is a card jam in the

The laminating temperature is too high or the speed is

 

card discharge area.

too slow. See “Card jam” on page 62 to clear the

 

 

jam.

 

 

 

Film search

The laminator is searching

Check that the laminating film is correctly loaded as

 

for laminate material.

described in “Load laminate” on page 11.

 

 

Press the RESET/K and then the ENTER key to

 

 

initialize the laminating material.

 

 

 

Film run out

The end of the roll mark

Replace the laminating material as described in “Load

 

has been detected.

laminate” on page 11.

 

 

Press the RESET/K and then the ENTER key to

 

 

initialize the laminator.

 

 

 

No Cassette

The laminator cartridge is

Install the laminator cartridge as described in “Load

 

not installed.

laminate” on page 11.

 

 

Press the RESET/K and then the ENTER key to

 

 

initialize the laminator.

 

 

 

Overcool

The area surrounding the

See “Operating environment” on page 72 for

 

laminator is too cold.

location guidelines.

 

 

 

HR is too hot!

The heat roller is too hot

Turn the power switch off and allow the roller to cool

 

for the cleaning operation.

before attempting to clean it. See “Cleaning the

 

 

laminator” on page 49 to clean the heat roller.

 

 

 

RP90 Plus E and RL90 User Guide

65

Image 71
Contents User Guide Regulatory compliance Contents Messages RP90 Plus E and RL90 User Guide Safe human interface SafetyLiability statement Safe environmentWho to call for assistance Introduction1About this manual Outside of the printer About the PrinterInside of the printer Back of the printer Parts of the laminator About the laminatorAbout the laminator RP90 Plus E and RL90 User Guide Using the printer See Supplies on page 67 for specific card information Load SuppliesLoad cards Tips Handling cardsTips Handling ink ribbon Load ink ribbonTips Handling retransfer film Load retransfer filmSee Laminator material on Load laminateTips Handling patch Or topcoat materialCheck the PC connection Power onOptional laminator connection LCD sequence on laminator startup Power on the laminatorTips for laminator power LCD sequence on printer startup Power on the printerTips for printer power Tips Ink ribbon Prepare to print cardsInitialize the ink ribbon Set the retransfer film typeInitialize the retransfer film Printing cards Print cards using ID softwareTips Printing Print from a PC applicationPrinting cards RP90 Plus E and RL90 User Guide Viewing and changing Printer settings Printing Preferences Setup tabEncode tab Printing Properties Tips Card cleaning rollerTips for Success Status MonitorOpen the Status Monitor Printer Status tab Close the Status MonitorSee Status monitor messages on Printer Setting tabIcon Status Icon Color Meaning Bend Remedy tab Retransfer tabDisplay Reasons for ink recognition error and the solutions Media Setting tabPrinter Select tab Property tabSee Hopper jam on page 52 to remove Status monitor messagesOthers tab Correctly see Load retransfer film on See Turnover jam on page 53 to removeSee Retransfer section jam on page 54 to Mending broken ink ribbon or retransfer Film onPower on the printer on page 15 Initialize the ink ribbon on Ink ribbon onPrinter LCD panel on Using the LCD menusAbout the Printer LCD panel Heat roller on page 45 or Cleaning the magnetic Using the Printer LCD panelMagnetic stripe cards. See Cleaning the card feed rollers Menu Display Menu Display USB See Preparing the printer and laminator for transport Menu About the Laminator LCD panelLaminator on page 49 for more information Using the Laminator LCD panelTaking care of your printer Load cards on Cleaning the printerCleaning the card cleaning rollers Card feed rollerPower on the printer. See Power on the printer on Cleaning the card feed rollers and heat rollerTips Cleaning card feed and heat rollers Tips -Magnetic head cleaning card Cleaning the magnetic headTips Thermal head Cleaning the thermal headCleaning printer fan filters Preparing the printer and laminator for transport Tips Laminator cleaning card Cleaning the laminatorRun a laminator cleaning card Laminator fan filter Cleaning the laminator cartridgePrinter roller layout Messages Error recoveryHopper jam Printer error recoveryTips Turnover jam Turnover jamTips Retransfer jam Retransfer section jamRibbon on page 16 or Initialize the retransfer film on Mending broken ink ribbon or retransfer filmRemedy tab on Bend remedy printer settingsBend remedy Tips -Bend RemedyTo set the laminator Card Fan Bend remedy laminator settingsSee Turnover jam on See Cleaning the card feed rollers and heatPrinter LCD messages See Hopper jam onMending broken ink ribbon or retransfer film As described in Operating environment on See Cleaning the card cleaning rollers onDescribed in Retransfer section jam on Tips Laminator card jam Laminator error recoveryCard jam Align the end of the supply material with Change the left-to-right position Patch positionLaminator LCD messages LCD Message Possible Cause Solution Supplies6 Retransfer film Ink ribbon, retransfer film, and laminator materialCards Ink ribbonCard material Cleaning suppliesCard size RP90 Plus E and RL90 User Guide Site requirements Tips Site selection Site guidelinesOperating environment Storage Environment for supplies Ventilation clearancePrinter specifications Laminator specifications RP90 Plus E and RL90 User Guide Inline Encoding on Character Code Table on Magnetic Stripe EncodingTip for success Inline EncodingExample DEL Character Code TableCharacter Code Table RP90 Plus E and RL90 User Guide Compliance FCC Regulatory compliance Design and information contained in these June