Datacard Group RL90, RP90 manual About the Laminator LCD panel, Menu

Page 47

Using the LCD menus

About the Laminator LCD panel

When you power on the laminator, it begins initializing. The laminator searches for laminate and then starts preheating. The laminator is ready when the LCD display reads "Ready" and the Ready light is steady green.

Ready LED (green)

Steady Green	The laminator is ready.
Blinking	The laminator busy.
Off	The laminator stopped because of an error, initialization or
	preheating is in progress, or the operator is using the LCD panel to
	set preferences.

Error LED (red)

On	The laminator may require service or did not power on correctly. To
	correct the condition, press the RESET/K and then the ENTER key.
	If this does not correct the condition, power the laminator off, and
	then back on before calling for service.
Off	Normal status

Keys:

MENU	Press MENU to access the laminator settings. Continue to press
	the MENU key to access the settings in the order listed on the next
	page.
ENTER	Confirms your selection.
EXIT	Exits the current selection and returns you to the previous menu
	selection. Press the EXIT key at any time to exit the menu system
	and return to "Ready" status.
RESET/K	Initializes the laminator after an error occurs. Scrolls through
	available values when you change settings.

RP90 Plus E and RL90 User Guide

41

Image 47

Contents User Guide Regulatory compliance Contents Messages RP90 Plus E and RL90 User Guide Safe human interface SafetyLiability statement Safe environmentWho to call for assistance Introduction1About this manual Outside of the printer About the PrinterInside of the printer Back of the printer Parts of the laminator About the laminatorAbout the laminator RP90 Plus E and RL90 User Guide Using the printer See Supplies on page 67 for specific card information Load SuppliesLoad cards Tips Handling cardsTips Handling ink ribbon Load ink ribbonTips Handling retransfer film Load retransfer filmSee Laminator material on Load laminateTips Handling patch Or topcoat materialCheck the PC connection Power onOptional laminator connection LCD sequence on laminator startup Power on the laminatorTips for laminator power LCD sequence on printer startup Power on the printerTips for printer power Tips Ink ribbon Prepare to print cardsInitialize the ink ribbon Set the retransfer film typeInitialize the retransfer film Printing cards Print cards using ID softwareTips Printing Print from a PC applicationPrinting cards RP90 Plus E and RL90 User Guide Viewing and changing Printer settings Printing Preferences Setup tabEncode tab Printing Properties Tips Card cleaning rollerTips for Success Status MonitorOpen the Status Monitor Printer Status tab Close the Status MonitorSee Status monitor messages on Printer Setting tabIcon Status Icon Color Meaning Bend Remedy tab Retransfer tabDisplay Reasons for ink recognition error and the solutions Media Setting tabPrinter Select tab Property tabSee Hopper jam on page 52 to remove Status monitor messagesOthers tab Correctly see Load retransfer film on See Turnover jam on page 53 to removeSee Retransfer section jam on page 54 to Mending broken ink ribbon or retransfer Film onPower on the printer on page 15 Initialize the ink ribbon on Ink ribbon onPrinter LCD panel on Using the LCD menusAbout the Printer LCD panel Heat roller on page 45 or Cleaning the magnetic Using the Printer LCD panelMagnetic stripe cards. See Cleaning the card feed rollers Menu Display Menu Display USB See Preparing the printer and laminator for transport Menu About the Laminator LCD panelLaminator on page 49 for more information Using the Laminator LCD panelTaking care of your printer Load cards on Cleaning the printerCleaning the card cleaning rollers Card feed rollerPower on the printer. See Power on the printer on Cleaning the card feed rollers and heat rollerTips Cleaning card feed and heat rollers Tips -Magnetic head cleaning card Cleaning the magnetic headTips Thermal head Cleaning the thermal headCleaning printer fan filters Preparing the printer and laminator for transport Tips Laminator cleaning card Cleaning the laminatorRun a laminator cleaning card Laminator fan filter Cleaning the laminator cartridgePrinter roller layout Messages Error recoveryHopper jam Printer error recoveryTips Turnover jam Turnover jamTips Retransfer jam Retransfer section jamRibbon on page 16 or Initialize the retransfer film on Mending broken ink ribbon or retransfer filmRemedy tab on Bend remedy printer settingsBend remedy Tips -Bend RemedyTo set the laminator Card Fan Bend remedy laminator settingsSee Turnover jam on See Cleaning the card feed rollers and heatPrinter LCD messages See Hopper jam onMending broken ink ribbon or retransfer film As described in Operating environment on See Cleaning the card cleaning rollers onDescribed in Retransfer section jam on Tips Laminator card jam Laminator error recoveryCard jam Align the end of the supply material with Change the left-to-right position Patch positionLaminator LCD messages LCD Message Possible Cause Solution Supplies6 Retransfer film Ink ribbon, retransfer film, and laminator materialCards Ink ribbonCard material Cleaning suppliesCard size RP90 Plus E and RL90 User Guide Site requirements Tips Site selection Site guidelinesOperating environment Storage Environment for supplies Ventilation clearancePrinter specifications Laminator specifications RP90 Plus E and RL90 User Guide Inline Encoding on Character Code Table on Magnetic Stripe EncodingTip for success Inline EncodingExample DEL Character Code TableCharacter Code Table RP90 Plus E and RL90 User Guide Compliance FCC Regulatory compliance Design and information contained in these June