Datacard Group RL90, RP90 manual Printer Setting tab, Icon Status Icon Color Meaning

Page 33

Status Monitor

The current state of the printer, such as ready. The icon changes with different states. See the table below.

Icon

Status

Icon Color

Meaning

 

 

 

 

 

 

 

 

 

No Printer is found.

Yellow

The printer power is not switched on. or the host PC and

 

 

 

printer are not connected properly by the USB cable.

 

 

 

 

 

Ready

Green

The printer is ready and able to start card printing.

 

 

 

 

 

Initializing

Yellow

The printer is initializing. After the printer is initialized, it

 

 

 

goes into Ready state.

 

 

 

 

 

Offline Mode

Yellow

The printer is in Setting mode or it is being cleaned.

 

 

 

When the process ends, it goes into Ready state.

 

 

 

 

 

Preheating

Yellow

The heat roller is heating. When it reaches the correct

 

 

 

temperature, the printer goes into Ready state.

 

 

 

 

 

Card Loading

Yellow

The printer is issuing cards. The operating status during

 

Card Transporting

 

card issuing is indicated. When the card is issued, the

 

MG Encoding

 

printer goes into Ready state.

 

Retransfer

 

 

 

Contact IC Encoding

 

 

 

No-Contact IC

 

 

 

Encoding

 

 

 

Unloading

 

 

 

Printing

 

 

 

 

 

 

 

Power Saving

Yellow

The printer is in power save mode. To end Power

 

 

 

Saving, press the RESET button on the printer and then

 

 

 

press the ENTER button to initialize the printer.

 

 

 

 

 

Error

Red

See “Status monitor messages” on page 31.

 

 

 

 

Printer Setting tab

The Printer Setting tab shows:

Controls for viewing or changing print settings:

Resin K Print Level, which sets the K resin ink print density.

Level of UV Ink and Level of Special Ink 2 which are not supported.

Resin K Print Mode which sets the K resin ink print quality. If Fine is selected, the print quality improves but the printing speed is slower.

Cooling Time which sets the time in seconds to wait until the retransfer film

peels off from the card after retransfer. The default value is 0.

RP90 Plus E and RL90 User Guide

27

Image 33
Contents User Guide Regulatory compliance Contents Messages RP90 Plus E and RL90 User Guide Liability statement SafetySafe environment Safe human interfaceIntroduction1 About this manualWho to call for assistance Outside of the printer About the PrinterInside of the printer Back of the printer Parts of the laminator About the laminatorAbout the laminator RP90 Plus E and RL90 User Guide Using the printer Load cards Load SuppliesTips Handling cards See Supplies on page 67 for specific card informationTips Handling ink ribbon Load ink ribbonTips Handling retransfer film Load retransfer filmTips Handling patch Load laminateOr topcoat material See Laminator material onCheck the PC connection Power onOptional laminator connection Power on the laminator Tips for laminator powerLCD sequence on laminator startup Power on the printer Tips for printer powerLCD sequence on printer startup Initialize the ink ribbon Prepare to print cardsSet the retransfer film type Tips Ink ribbonInitialize the retransfer film Printing cards Print cards using ID softwareTips Printing Print from a PC applicationPrinting cards RP90 Plus E and RL90 User Guide Viewing and changing Printer settings Printing Preferences Setup tabEncode tab Printing Properties Tips Card cleaning rollerStatus Monitor Open the Status MonitorTips for Success Printer Status tab Close the Status MonitorPrinter Setting tab Icon Status Icon Color MeaningSee Status monitor messages on Bend Remedy tab Retransfer tabDisplay Reasons for ink recognition error and the solutions Media Setting tabPrinter Select tab Property tabStatus monitor messages Others tabSee Hopper jam on page 52 to remove See Retransfer section jam on page 54 to See Turnover jam on page 53 to removeMending broken ink ribbon or retransfer Film on Correctly see Load retransfer film onPower on the printer on page 15 Initialize the ink ribbon on Ink ribbon onUsing the LCD menus About the Printer LCD panelPrinter LCD panel on Using the Printer LCD panel Magnetic stripe cards. See Cleaning the card feed rollersHeat roller on page 45 or Cleaning the magnetic Menu Display Menu Display USB See Preparing the printer and laminator for transport Menu About the Laminator LCD panelLaminator on page 49 for more information Using the Laminator LCD panelTaking care of your printer Cleaning the card cleaning rollers Cleaning the printerCard feed roller Load cards onCleaning the card feed rollers and heat roller Tips Cleaning card feed and heat rollersPower on the printer. See Power on the printer on Tips -Magnetic head cleaning card Cleaning the magnetic headCleaning the thermal head Cleaning printer fan filtersTips Thermal head Preparing the printer and laminator for transport Cleaning the laminator Run a laminator cleaning cardTips Laminator cleaning card Laminator fan filter Cleaning the laminator cartridgePrinter roller layout Messages Error recoveryHopper jam Printer error recoveryTips Turnover jam Turnover jamTips Retransfer jam Retransfer section jamRibbon on page 16 or Initialize the retransfer film on Mending broken ink ribbon or retransfer filmBend remedy Bend remedy printer settingsTips -Bend Remedy Remedy tab onTo set the laminator Card Fan Bend remedy laminator settingsPrinter LCD messages See Cleaning the card feed rollers and heatSee Hopper jam on See Turnover jam onMending broken ink ribbon or retransfer film As described in Operating environment on See Cleaning the card cleaning rollers onDescribed in Retransfer section jam on Laminator error recovery Card jamTips Laminator card jam Align the end of the supply material with Change the left-to-right position Patch positionLaminator LCD messages LCD Message Possible Cause Solution Supplies6 Cards Ink ribbon, retransfer film, and laminator materialInk ribbon Retransfer filmCleaning supplies Card sizeCard material RP90 Plus E and RL90 User Guide Site requirements Site guidelines Operating environmentTips Site selection Storage Environment for supplies Ventilation clearancePrinter specifications Laminator specifications RP90 Plus E and RL90 User Guide Inline Encoding on Character Code Table on Magnetic Stripe EncodingInline Encoding ExampleTip for success DEL Character Code TableCharacter Code Table RP90 Plus E and RL90 User Guide Compliance FCC Regulatory compliance Design and information contained in these June