Novatel SMART-AG user manual Index

Page 73

Index

A

accuracy position, 29, 50 velocity, 50

almanac, 58 antenna

internal, 18 mounting, 23 single-frequency,23 specifications, 51

ascii, 41

AUTH command, 44 authorization, 45 AUX port, 63

B

base station, 33 baseline, 29 baud rate, 26

bidirectional communication, 27 Bluetooth, 21

buffer, 26, 59

C

cable serial, 26 warranty, 9

Caution, 26

CDU software, 35, 60, 72 CMR, 33

cold start, 50 COM port, 60 command, 57 CDU, 28

communication, 26 error message, 28 example, 28

in CDU, 39, 44 interface, 33 multiple, 34 note, 28

port, 26 pre-configure,31 prompt, 28 RTK, 33

communication bidirectional, 27 CDU, 28 getting started, 27 notice, 13 operation, 26 PC/laptop, 27 physical, 20 port, 23, 26 remote terminal, 27

COMVOUT command, 58 configuration

additional equipment, 20 base station, 31

CDU, 27 model, 18 port, 23, 26 rover station, 32 RTK, 33

typical hardware, 26 connector

input/output, 51 mounting bracket, 22 specifications, 51

Controller Area Network Bus (CAN Bus),

23

Convert software, 41 copyright, 2

CPU, 59

Customer Service, 15, 44

D

data

collect, 24 erase, 58 format, 57 L-band,58 link, 30

SMART-AG User Manual Rev 2

73

Image 73
Contents SMART-AG User Manual Proprietary Notice Introduction Table of ContentsPC Utilities Technical Specifications Tables Figures Restrictions You may not Software LicenseSoftware License SMART-AG WarrantyStandard Terms and Conditions of Sales Terms and Conditions Terms and Conditions FCC Notices SMART-AG Regulatory Testing Electromagnetic Compatibility EMC and SafetyWeee Notice RoHS NoticeOemv Firmware Upgrades Customer ServiceCongratulations ForewordConventions Chapter Introduction Models and FeaturesSMART-AG Controller Models Model Name Firmware FeatureSMART-AG Setup Chapter Installation and SetupAdditional Equipment Required Simplified SMART-AG Setup SMART-AG Connector Pin-OutPower Supply Requirements Installing the PC UtilitiesMounting Bracket Connecting Data Communications Equipment Additional Features and InformationStatus Indicators Mounting the SMART-AGSMART-AG LED Status Indicators Can SetupEmulated Radar ER Available can Signals on the SMART-AGNema Standards Chapter Operation Serial Port Default SettingsCommunications with the Receiver Communicating Using a Personal Computer Communicating Using a Remote TerminalCommunicating with the Receiver Using CDU Getting StartedChapter Operation Transmitting and Receiving Corrections Description Basic Differential SetupLog port message trigger period Base Station ConfigurationGPS + Glonass Base and Rover Configuration Rover Station ConfigurationRecommended Configuration Configuration Notes Chapter Operation Chapter PC Utilities CDU/Convert InstallationCDU PC Utilities Chapter Chapter Gdop Chapter Rinex Format ConvertChapter NovAtel Logs for Rinex Conversion Convert Command Line SwitchesUpgrading Using the Auth Command Firmware UpgradesTransferring Firmware Files Updating Using the WinLoad UtilityUsing the WinLoad Utility Open a File to Download Downloading firmware Upgrade Process Complete Appendix a SMART-AG Specifications Dimensions SMART-AG Power/Communications Development kit Cable SMART-AG Cable Pinouts Colour Signal Name LabelSMART-AG Mating Connectors Fuse Recommended Fuse/Fuse Holder Recommended Fuse and Fuse HoldersAppendix B SMART-AG Commands in Alphabetical OrderFreset Target FresetLOG Abbreviated Ascii SyntaxMessage ID Description Field Name Value Type Detailed Serial Port Identifiers THISPORT31 Radarcfg Response Modes Mode DescriptionReset SMART-AG Logs in Alphabetical Order Appendix CRadarsignal Type binary Type Ascii Description Position or Velocity TypePending Solution StatusComponent Type Version HW & SW Versions and Serial NumbersAppendix D Replacement Parts Index Index Log OM-20000123 Rev 2008/12/16