Ultimate Technology 600 POS manual Programming Keyboard Operating Parameters

Page 18

PROGRAMMING

PROGRAMMING KEYBOARD OPERATING PARAMETERS

The operating parameters of the keyboard can be configured (programmed) remotely from the host computer or locally at the keyboard. Keyboard programming in the remote mode sets the keyboard parameters as commanded by the host computer input applied at the main communications port. Selection of the local programming mode enables keyboard parameter setup locally at the keyboard. Note: All keyboards come from the factory programmed with

a default set of parameters.

LOCAL MODE PROGRAMMING INSTRUCTIONS

To program the Series 600 Keyboard in the local mode proceed as follows:

1.Connect main keyboard port to PC or Host, Aux keyboard port to IBM Compatible PC keyboard.

2.Swipe the PROGRAM CARD supplied with the keyboard in the magnetic stripe reader MSR).

3.All LED indicators turn on and the keyboard annunicator beeps three times.

4.After step 3 is complete, LED indicator (1) will flash continuously to indicate that the keyboard programming mode is active.

5.For a summary of the parameters that can be programmed in the local mode, refer to Table 3.

6.Follow the instructions given in Table 2 for the applicable Function Code(s) to program the keyboard for the desired parameter(s). Note that sequence of instructions provided in Table 2 is in Function Code numerical order.

7.When programming is complete, exit the local programming mode by typing 99 on the Series 600 Keyboard numeric keypad or by swiping the Program Card. This returns the keyboard to normal operation.

NOTE

Some programming options may not be activated until the keyboard is re-powered. Serial port communication selections -- Function Codes 20-24; 30-34; 91.

Series 600 POS Keyboard

13

Image 18
Contents Programming & USER’S Guide Table of Contents Maintenance Appendix List of TablesList of Figures Series 600 POS Keyboard Scope Special NoteSeries 600 POS Keyboard Features Product InformationModel Description BUILT-IN Diagnostics BUILT-IN AnnunciatorWeight Approvals Service and WarrantySpecifications EnvironmentInstallation Unpacking and InspectionPrinter 1, 2 Pinouts External ConnectionsCash Drawer Jumper Connections Printer Fired Driver 1Main RS232 Typical Keyboard External Connections Keyboard External Connectors Rear View DescriptionControls and Indicators OperationSeries 600 POS Keyboard Local Mode Programming Instructions ProgrammingProgramming Keyboard Operating Parameters LED 2 turns on LED 2 flashesLED 2 stops flashing LED 2 turns off Local Mode Programming Instructions = Default Settings Local Mode Programming Instructions = Default Settings List below to select MSR data from one or both good tracks 20 or 21 or22 or 23 or24 or 25 or26 or Turns Series 600 POS Keyboard Cash Drawer Status Local Mode Programming Instructions = Default Settings Numeric keypad, enter Function Code 80 or Define Left Shift Alternate Local Mode Programming Instructions = Default Settings Function Parameter Default Remarks Code Function Parameter Default Remarks Code Setting Function Parameter Default Remarks Code Setting Executed Local Mode programming Function Codes and Default Settings Swiping the Programmers card Series Keyboard Description Numeric Keypad no BreakExample Example Programming in Remote Mode Series 600 POS Keyboard Command A0krcCxDx.......CR Acknowledgement NoneCommand A1aCxDx.......CR Commp Command A5xCxDxCR Clicked CommandA4xxxx-xxxxCR A6xCRNvbdwr Command Nvbdclr Command A9CLRCRCdsecopn ADxCR Secure CommandComment Command AExCRCommand B0LxCR B1pdCR B2p...........CRCommit Command Command B5RSTCRKssnd Command OP Code MNEMONIC/DESCRIPTION COMMAND/ACKNOWLEDGEMENT HEX Msrsnd CommandCarded Command Cdcont Command BApCRBBpCR Acknowledgement Porte CommandBCpCR BDpxCRBEnnnnnvvvvkkkkx-xCR Command Bfcr101/102-KEY Keyboard KEY Code Identification BF...............CRRemote Description Programming Command Remote Programming KEY MAKE/BREAK CodesWhere A0 Examples of Remote Programming for KEY MAKE/BREAK CodeExample Example Opos Programming OposPrefix MSR Programming for UTC Opos DriversTrack SuffixMSR Series 500 Main Copying Keyboard Setup Data CloningSource Unit Destination Unit SeriesOperators and Programmers Magnetic Cards System LOGMaintenance PrecautionsCleaning Battery Replacement KEY Legend Change Inch Full Travel KeyboardsSeries 600 POS Keyboard Appendix a Series 600 POS Standard Keyboard Layouts Appendix a Series 600 POS Standard Keyboard LayoutsAppendix B Keyboard CABLE/CONNECTOR Data Back Connector PinoutsAppendix C Ascii Character SET DLEScan Code KEY Number Decimal Hexadecimal2B/AB Scan Code KEY Number 4F/CF 3B/BB E1 14 77 E1 62/F0 9D C5 F0 14 F0 Ultimate Technology Corporation VICTOR, NEW York