Ultimate Technology 600 POS manual Scope, Special Note

Page 6

SCOPE

This user's guide provides the information and procedures needed to install, operate and program your Series 600 POS Keyboard. Differences in models and optional features are described in this manual, where applicable. It is suggested that the entire manual be read before attempting installation or programming. If assistance is needed that is beyond the coverage provided in this guide, please contact Customer Service:

Ultimate Technology Corporation

100 Rawson Road Victor New York, 14564 Phone: (800) 349-0546 Fax: (585) 924-1434

E-mail: sales@ultimatetechnology.com

SPECIAL NOTE

When this publication was written, every effort was made to ensure that information in this document was complete, accurate, and up to date. Ultimate Technology Corporation assumes no responsibility for errors beyond its control. Ultimate Technology Corporation also cannot guarantee that changes in software and equipment made by other manufacturers, and referenced in this guide, do not effect the applicability of the information in this manual. If assistance is needed, please contact Customer Service at the address or phone number given above.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT OPEN KEYBOARD ENCLOSURE WHEN

KEYBOARD IS CONNECTED TO SYSTEM.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE KEYBOARD TO RAIN OR MOISTURE.

Contents of this publication may be changed without notice and shall not be regarded as a warranty.

Series 600 POS Keyboard

1

Image 6

Contents Programming & USER’S Guide Table of Contents Maintenance Appendix List of TablesList of Figures Series 600 POS Keyboard Scope Special NoteSeries 600 POS Keyboard Features Product InformationModel Description BUILT-IN Diagnostics BUILT-IN AnnunciatorWeight Approvals Service and WarrantySpecifications EnvironmentInstallation Unpacking and InspectionPrinter 1, 2 Pinouts External ConnectionsCash Drawer Jumper Connections Printer Fired Driver 1Main RS232 Typical Keyboard External Connections Keyboard External Connectors Rear View DescriptionControls and Indicators OperationSeries 600 POS Keyboard Local Mode Programming Instructions ProgrammingProgramming Keyboard Operating Parameters LED 2 turns on LED 2 flashesLED 2 stops flashing LED 2 turns off Local Mode Programming Instructions = Default Settings Local Mode Programming Instructions = Default Settings List below to select MSR data from one or both good tracks 20 or 21 or22 or 23 or24 or 25 or26 or Turns Series 600 POS Keyboard Cash Drawer Status Local Mode Programming Instructions = Default Settings Numeric keypad, enter Function Code 80 or Define Left Shift Alternate Local Mode Programming Instructions = Default Settings Function Parameter Default Remarks Code Function Parameter Default Remarks Code Setting Function Parameter Default Remarks Code Setting Executed Local Mode programming Function Codes and Default Settings Swiping the Programmers card Series Keyboard Description Numeric Keypad no BreakExample Example Programming in Remote Mode Series 600 POS Keyboard Command A0krcCxDx.......CR Acknowledgement NoneCommand A1aCxDx.......CR Commp Command A5xCxDxCR Clicked CommandA4xxxx-xxxxCR A6xCRNvbdwr Command Nvbdclr Command A9CLRCRCdsecopn ADxCR Secure CommandComment Command AExCRCommand B0LxCR B1pdCR B2p...........CRCommit Command Command B5RSTCRKssnd Command OP Code MNEMONIC/DESCRIPTION COMMAND/ACKNOWLEDGEMENT HEX Msrsnd CommandCarded Command Cdcont Command BApCRBBpCR Acknowledgement Porte CommandBCpCR BDpxCRBEnnnnnvvvvkkkkx-xCR Command Bfcr101/102-KEY Keyboard KEY Code Identification BF...............CRRemote Description Programming Command Remote Programming KEY MAKE/BREAK CodesWhere A0 Examples of Remote Programming for KEY MAKE/BREAK CodeExample Example Opos Programming OposPrefix MSR Programming for UTC Opos DriversTrack SuffixMSR Series 500 Main Copying Keyboard Setup Data CloningSource Unit Destination Unit SeriesOperators and Programmers Magnetic Cards System LOGMaintenance PrecautionsCleaning Battery Replacement KEY Legend Change Inch Full Travel KeyboardsSeries 600 POS Keyboard Appendix a Series 600 POS Standard Keyboard Layouts Appendix a Series 600 POS Standard Keyboard LayoutsAppendix B Keyboard CABLE/CONNECTOR Data Back Connector PinoutsAppendix C Ascii Character SET DLEScan Code KEY Number Decimal Hexadecimal2B/AB Scan Code KEY Number 4F/CF 3B/BB E1 14 77 E1 62/F0 9D C5 F0 14 F0 Ultimate Technology Corporation VICTOR, NEW York