Ultimate Technology 600 POS manual Alternate

Page 33

Table 2. Local Mode Programming Instructions

* = Default Settings

	Function Code(s)	Operation		Normal Indication		Remarks

	84	1.	Swipe	Program Card.	While in programming	mode, at the Series	600 Keyboard
	84		numeric keypad, enter Function Code 84 or 85.
	85		numeric keypad, enter Function Code 84 or 85.
	85
	Define Left		LED (2) flashes.
	ALTERNATE
	Key (84) and	2.	At the auxiliary keyboard, hit the left ALTERNATE key if programming Function Code
	Right ALTERNATE		84 or right ALTERNATE key if programming Function Code 85.
	Right ALTERNATE
	Key (85)	3.	At the Series 600 Keyboard, press ENTER.
	Key (85)
			LED (2) turns off.
		4.	Program the next function code or exit programming mode by entering 99 on Series
			600 Keyboard numeric keypad or by swiping the program Card.

	90	This is a command used to read out the Series 600 Keyboard system log data at the main
	90	port. For		detailed information about retrieving		the system log data,	refer to the
	Dump System Log	port. For		detailed information about retrieving		the system log data,	refer to the
	Dump System Log	Maintenance Section of this manual.
		Maintenance Section of this manual.

	91	1.	Swipe	Program Card.	While in programming	mode, at the Series	600 Keyboard
	Main Port Select		numeric keypad, enter Function Code 91.
			LED (2) turns on.
		2.	At Series 600 Keyboard numeric keypad, enter the applicable number.
			0 = Keyboard Port 0 is main
			1 = RS232 Port 0 is main
			2 = Keyboard Port 0 is main, but RS232 Port 0 will accept commands
			LED (2) turns off.
		3.	Program the next function code or exit programming mode by entering 99 on Series
			600 Keyboard numeric keypad or by swiping the Program Card.
			Note: Must re-power Series 600 Keyboard in order to activate function code.

Series 600 POS Keyboard

28

Image 33

Contents Programming & USER’S Guide Table of Contents Maintenance Appendix List of TablesList of Figures Series 600 POS Keyboard Special Note ScopeSeries 600 POS Keyboard Features Product InformationModel Description BUILT-IN Annunciator BUILT-IN DiagnosticsSpecifications Service and WarrantyWeight Approvals EnvironmentUnpacking and Inspection InstallationCash Drawer Jumper Connections Printer Fired External ConnectionsPrinter 1, 2 Pinouts Driver 1Main RS232 Typical Keyboard External Connections Description Keyboard External Connectors Rear ViewOperation Controls and IndicatorsSeries 600 POS Keyboard Local Mode Programming Instructions ProgrammingProgramming Keyboard Operating Parameters LED 2 turns on LED 2 flashesLED 2 stops flashing LED 2 turns off Local Mode Programming Instructions = Default Settings Local Mode Programming Instructions = Default Settings List below to select MSR data from one or both good tracks 21 or 20 or23 or 22 or25 or 24 or26 or Turns Series 600 POS Keyboard Cash Drawer Status Local Mode Programming Instructions = Default Settings Numeric keypad, enter Function Code 80 or Define Left Shift Alternate Local Mode Programming Instructions = Default Settings Function Parameter Default Remarks Code Function Parameter Default Remarks Code Setting Function Parameter Default Remarks Code Setting Executed Local Mode programming Function Codes and Default Settings Swiping the Programmers card Break Series Keyboard Description Numeric Keypad noExample Example Programming in Remote Mode Series 600 POS Keyboard Acknowledgement None Command A0krcCxDx.......CRCommand A1aCxDx.......CR Commp Command A4xxxx-xxxxCR Clicked CommandA5xCxDxCR A6xCRNvbdwr Command Nvbdclr Command A9CLRCRCdsecopn Comment Command Secure CommandADxCR AExCRCommand B0LxCR B2p...........CR B1pdCRCommit Command Command B5RSTCRKssnd Command OP Code MNEMONIC/DESCRIPTION COMMAND/ACKNOWLEDGEMENT HEX Msrsnd CommandCarded Command Cdcont Command BApCRBBpCR BCpCR Porte CommandAcknowledgement BDpxCR101/102-KEY Keyboard KEY Code Identification Command BfcrBEnnnnnvvvvkkkkx-xCR BF...............CRRemote Programming KEY MAKE/BREAK Codes Remote Description Programming CommandExamples of Remote Programming for KEY MAKE/BREAK Code Where A0Example Example Opos Opos ProgrammingTrack MSR Programming for UTC Opos DriversPrefix SuffixMSR Source Unit Destination Unit Copying Keyboard Setup Data CloningSeries 500 Main SeriesSystem LOG Operators and Programmers Magnetic CardsMaintenance PrecautionsCleaning KEY Legend Change Inch Full Travel Keyboards Battery ReplacementSeries 600 POS Keyboard Appendix a Series 600 POS Standard Keyboard Layouts Series 600 POS Standard Keyboard Layouts Appendix aBack Connector Pinouts Appendix B Keyboard CABLE/CONNECTOR DataDLE Appendix C Ascii Character SETDecimal Hexadecimal Scan Code KEY Number2B/AB Scan Code KEY Number 4F/CF 3B/BB E1 14 77 E1 62/F0 9D C5 F0 14 F0 VICTOR, NEW York Ultimate Technology Corporation