Ultimate Technology manual Series 600 POS Keyboard

Page 70

1.Disconnect keyboard from system.

2.Turn keyboard over to gain access to 7 screws that secure the base of the keyboard case to the top. Remove the 7 screws.

3.Turn keyboard upright. Gain access to the battery by lifting the top portion of the keyboard assembly from the base and placing it and the attached extended cable/connectors in front of the base.

CAUTION

Replacement of the battery may result in the need to reprogram the keyboard. For programming instructions, refer to the programming section of this manual.

4.Remove existing battery.

5.Making sure to observe correct polarity, install a new 3-volt lithium battery in the keyboard using one of the approved replacement batteries listed below, or an equivalent. Note that sweat and oil can prevent a battery's terminals from making electrical contact. To avoid this, wipe both sides before installing battery.

Panasonic, Part No. BR2032

6.Make sure that the cable/connectors are making good contact, then position the top of the keyboard assembly on the keyboard base. Turn the keyboard over and secure top of the keyboard to the base by installing the 7 screws.

7.Connect keyboard to system.

8.Dispose of the used battery in an environmentally safe manner. If necessary, the battery may be returned to the Ultimate Technology Corporation at the address shown below for proper disposal.

Ultimate Technology Corporation

100 Rawson Road

Victor, NY 14564

Phone (800) 349-0546

Series 600 POS Keyboard

65

Image 70
Contents Programming & USER’S Guide Table of Contents Maintenance List of Tables AppendixList of Figures Series 600 POS Keyboard Scope Special NoteSeries 600 POS Keyboard Product Information FeaturesModel Description BUILT-IN Diagnostics BUILT-IN AnnunciatorWeight Approvals Service and WarrantySpecifications EnvironmentInstallation Unpacking and InspectionPrinter 1, 2 Pinouts External ConnectionsCash Drawer Jumper Connections Printer Fired Driver 1Main RS232 Typical Keyboard External Connections Keyboard External Connectors Rear View DescriptionControls and Indicators OperationSeries 600 POS Keyboard Programming Local Mode Programming InstructionsProgramming Keyboard Operating Parameters LED 2 flashes LED 2 turns onLED 2 stops flashing LED 2 turns off Local Mode Programming Instructions = Default Settings Local Mode Programming Instructions = Default Settings List below to select MSR data from one or both good tracks 20 or 21 or22 or 23 or24 or 25 or26 or Turns Series 600 POS Keyboard Cash Drawer Status Local Mode Programming Instructions = Default Settings Numeric keypad, enter Function Code 80 or Define Left Shift Alternate Local Mode Programming Instructions = Default Settings Function Parameter Default Remarks Code Function Parameter Default Remarks Code Setting Function Parameter Default Remarks Code Setting Executed Local Mode programming Function Codes and Default Settings Swiping the Programmers card Series Keyboard Description Numeric Keypad no BreakExample Example Programming in Remote Mode Series 600 POS Keyboard Command A0krcCxDx.......CR Acknowledgement NoneCommand A1aCxDx.......CR Commp Command A5xCxDxCR Clicked CommandA4xxxx-xxxxCR A6xCRNvbdclr Command A9CLRCR Nvbdwr CommandCdsecopn ADxCR Secure CommandComment Command AExCRCommand B0LxCR B1pdCR B2p...........CRCommand B5RSTCR Commit CommandKssnd Command Msrsnd Command OP Code MNEMONIC/DESCRIPTION COMMAND/ACKNOWLEDGEMENT HEXCarded Command BApCR Cdcont CommandBBpCR Acknowledgement Porte CommandBCpCR BDpxCRBEnnnnnvvvvkkkkx-xCR Command Bfcr101/102-KEY Keyboard KEY Code Identification BF...............CRRemote Description Programming Command Remote Programming KEY MAKE/BREAK CodesWhere A0 Examples of Remote Programming for KEY MAKE/BREAK CodeExample Example Opos Programming OposPrefix MSR Programming for UTC Opos DriversTrack SuffixMSR Series 500 Main Copying Keyboard Setup Data CloningSource Unit Destination Unit SeriesOperators and Programmers Magnetic Cards System LOGPrecautions MaintenanceCleaning Battery Replacement KEY Legend Change Inch Full Travel KeyboardsSeries 600 POS Keyboard Appendix a Series 600 POS Standard Keyboard Layouts Appendix a Series 600 POS Standard Keyboard LayoutsAppendix B Keyboard CABLE/CONNECTOR Data Back Connector PinoutsAppendix C Ascii Character SET DLEScan Code KEY Number Decimal Hexadecimal2B/AB Scan Code KEY Number 4F/CF 3B/BB E1 14 77 E1 62/F0 9D C5 F0 14 F0 Ultimate Technology Corporation VICTOR, NEW York