Ultimate Technology 600 POS manual Msr

Page 65

Table 8 MSR Programming for UTC OPOS Drivers

Function Code (s)		Operation
	1.	Swipe Program Card. While in programming mode, at the Series 600 Keyboard, enter
Track 2		Function Code 16 (suffix).
	2.	At the auxiliary keyboard, type ?<CR>.
16 (suffix)	3.	At the Series 600 Keyboard, press ENTER.

	1.	Swipe program Card. While in programming mode, at the Series 600 keyboard, enter
Track 2		Function Code 18 (bad read).
	2.	At the auxiliary keyboard, type c21?<CR>
18 (bad read)	3. At the Series 600 Keyboard, press ENTER.

	1.	Swipe Program Card. While in programming mode, at the Series 600 Keyboard, enter
MSR		Function Code 08 (track options).
	2.	At the Series 600 Keyboard numeric keypad, enter sub-function 7 (OPOS mode for
08 (track options)		MSR).
	3.	At the auxiliary keyboard, type c11?
	4.	Press enter on the keypad.

Series 600 POS Keyboard

60

Image 65

Contents Programming & USER’S Guide Table of Contents Maintenance List of Figures AppendixList of Tables Series 600 POS Keyboard Special Note ScopeSeries 600 POS Keyboard Model Description FeaturesProduct Information BUILT-IN Annunciator BUILT-IN DiagnosticsSpecifications Service and WarrantyWeight Approvals EnvironmentUnpacking and Inspection InstallationCash Drawer Jumper Connections Printer Fired External ConnectionsPrinter 1, 2 Pinouts Driver 1Main RS232 Typical Keyboard External Connections Description Keyboard External Connectors Rear ViewOperation Controls and IndicatorsSeries 600 POS Keyboard Programming Keyboard Operating Parameters Local Mode Programming InstructionsProgramming LED 2 stops flashing LED 2 turns onLED 2 flashes LED 2 turns off Local Mode Programming Instructions = Default Settings Local Mode Programming Instructions = Default Settings List below to select MSR data from one or both good tracks 21 or 20 or23 or 22 or25 or 24 or26 or Turns Series 600 POS Keyboard Cash Drawer Status Local Mode Programming Instructions = Default Settings Numeric keypad, enter Function Code 80 or Define Left Shift Alternate Local Mode Programming Instructions = Default Settings Function Parameter Default Remarks Code Function Parameter Default Remarks Code Setting Function Parameter Default Remarks Code Setting Executed Local Mode programming Function Codes and Default Settings Swiping the Programmers card Break Series Keyboard Description Numeric Keypad noExample Example Programming in Remote Mode Series 600 POS Keyboard Acknowledgement None Command A0krcCxDx.......CRCommand A1aCxDx.......CR Commp Command A4xxxx-xxxxCR Clicked CommandA5xCxDxCR A6xCRCdsecopn Nvbdwr CommandNvbdclr Command A9CLRCR Comment Command Secure CommandADxCR AExCRCommand B0LxCR B2p...........CR B1pdCRKssnd Command Commit CommandCommand B5RSTCR Carded Command OP Code MNEMONIC/DESCRIPTION COMMAND/ACKNOWLEDGEMENT HEXMsrsnd Command BBpCR Cdcont CommandBApCR BCpCR Porte CommandAcknowledgement BDpxCR101/102-KEY Keyboard KEY Code Identification Command BfcrBEnnnnnvvvvkkkkx-xCR BF...............CRRemote Programming KEY MAKE/BREAK Codes Remote Description Programming CommandExamples of Remote Programming for KEY MAKE/BREAK Code Where A0Example Example Opos Opos ProgrammingTrack MSR Programming for UTC Opos DriversPrefix SuffixMSR Source Unit Destination Unit Copying Keyboard Setup Data CloningSeries 500 Main SeriesSystem LOG Operators and Programmers Magnetic CardsCleaning MaintenancePrecautions KEY Legend Change Inch Full Travel Keyboards Battery ReplacementSeries 600 POS Keyboard Appendix a Series 600 POS Standard Keyboard Layouts Series 600 POS Standard Keyboard Layouts Appendix aBack Connector Pinouts Appendix B Keyboard CABLE/CONNECTOR DataDLE Appendix C Ascii Character SETDecimal Hexadecimal Scan Code KEY Number2B/AB Scan Code KEY Number 4F/CF 3B/BB E1 14 77 E1 62/F0 9D C5 F0 14 F0 VICTOR, NEW York Ultimate Technology Corporation