Ultimate Technology 600 POS manual Function Parameter Default Remarks Code

Page 35

LOCAL MODE PROGRAMMING

KEY MAKE/BREAK CODES AND EXTENDED FUNCTIONS

A summary of all keyboard parameters programmable in the local mode, assigned Function Codes and factory default settings is given in Table 3.

Table 3. Local Mode programming Function Codes and Default Settings

FUNCTION

PARAMETER

DEFAULT

REMARKS

CODE

 

SETTING (XXh

 

 

 

= Hex Code in

 

 

 

ASCII)

 

00

Program Keyboard Primary Keys

See default

Used to program primary keys on

 

 

(Appendix A)

Series 600 Keyboard. The keys can

 

 

 

be programmed to have primary and

 

 

 

secondary levels of function. The

 

 

 

primary function is activated when only

 

 

 

the designated key is pressed. The

 

 

 

secondary function is activated when

 

 

 

both the Sec Op key and designated

 

 

 

key are depressed. Use Function

 

 

 

Code 01 to program secondary key

 

 

 

functions.

01

Program Keyboard Secondary

See default

See remarks above.

 

Keys

 

 

02

Copy Primary Keys to Secondary

None

Used to copy primary key code into

 

Keys

 

key secondary position

03

Program Primary OPOS Keys

None

To be used in conjunction with UTC

 

 

 

OPOS drivers.

04

Program Secondary OPOS Keys

None

To be used in conjunction with UTC

 

 

 

OPOS drivers

08

Enable/Disable Magnetic Stripe

Channels 1,2

The magnetic card reader can read

 

Reader (MSR) Tracks

enabled

three formats of information, two at

 

 

 

any one time, on standard format

 

 

 

cards. This function is used to select

 

 

 

which tracks on the MSR are enabled

 

 

 

and/or disabled.

09

MSR Beep Configuration

Beep on good

Useful for indicating a good or bad

 

 

and bad read

reading when card swiped through

 

 

 

reader. (Uses different tones)

10

MSR Track 1,3 Prefix

% (25h) for

Used to send a prefix before the

 

 

format 1

magnetic card track data.

 

 

;(3Bh) for

 

 

 

format 3

 

11

MSR Track 1,3 Field Separator

^(5Eh) for

Used to send a field separator

 

 

format 1 =

between fields of magnetic card data.

 

 

(3Dh) for

 

 

 

format 3

 

Series 600 POS Keyboard

30

 

Image 35
Contents Programming & USER’S Guide Table of Contents Maintenance List of Figures AppendixList of Tables Series 600 POS Keyboard Special Note ScopeSeries 600 POS Keyboard Model Description FeaturesProduct Information BUILT-IN Annunciator BUILT-IN DiagnosticsEnvironment Service and WarrantySpecifications Weight ApprovalsUnpacking and Inspection InstallationDriver 1 External ConnectionsCash Drawer Jumper Connections Printer Fired Printer 1, 2 PinoutsMain RS232 Typical Keyboard External Connections Description Keyboard External Connectors Rear ViewOperation Controls and IndicatorsSeries 600 POS Keyboard Programming Keyboard Operating Parameters Local Mode Programming InstructionsProgramming LED 2 stops flashing LED 2 turns onLED 2 flashes LED 2 turns off Local Mode Programming Instructions = Default Settings Local Mode Programming Instructions = Default Settings List below to select MSR data from one or both good tracks 21 or 20 or23 or 22 or25 or 24 or26 or Turns Series 600 POS Keyboard Cash Drawer Status Local Mode Programming Instructions = Default Settings Numeric keypad, enter Function Code 80 or Define Left Shift Alternate Local Mode Programming Instructions = Default Settings Function Parameter Default Remarks Code Function Parameter Default Remarks Code Setting Function Parameter Default Remarks Code Setting Executed Local Mode programming Function Codes and Default Settings Swiping the Programmers card Break Series Keyboard Description Numeric Keypad noExample Example Programming in Remote Mode Series 600 POS Keyboard Acknowledgement None Command A0krcCxDx.......CRCommand A1aCxDx.......CR Commp Command A6xCR Clicked CommandA4xxxx-xxxxCR A5xCxDxCRCdsecopn Nvbdwr CommandNvbdclr Command A9CLRCR AExCR Secure CommandComment Command ADxCRCommand B0LxCR B2p...........CR B1pdCRKssnd Command Commit CommandCommand B5RSTCR Carded Command OP Code MNEMONIC/DESCRIPTION COMMAND/ACKNOWLEDGEMENT HEXMsrsnd Command BBpCR Cdcont CommandBApCR BDpxCR Porte CommandBCpCR AcknowledgementBF...............CR Command Bfcr101/102-KEY Keyboard KEY Code Identification BEnnnnnvvvvkkkkx-xCRRemote Programming KEY MAKE/BREAK Codes Remote Description Programming CommandExamples of Remote Programming for KEY MAKE/BREAK Code Where A0Example Example Opos Opos ProgrammingSuffix MSR Programming for UTC Opos DriversTrack PrefixMSR Series Copying Keyboard Setup Data CloningSource Unit Destination Unit Series 500 MainSystem LOG Operators and Programmers Magnetic CardsCleaning MaintenancePrecautions KEY Legend Change Inch Full Travel Keyboards Battery ReplacementSeries 600 POS Keyboard Appendix a Series 600 POS Standard Keyboard Layouts Series 600 POS Standard Keyboard Layouts Appendix aBack Connector Pinouts Appendix B Keyboard CABLE/CONNECTOR DataDLE Appendix C Ascii Character SETDecimal Hexadecimal Scan Code KEY Number2B/AB Scan Code KEY Number 4F/CF 3B/BB E1 14 77 E1 62/F0 9D C5 F0 14 F0 VICTOR, NEW York Ultimate Technology Corporation