Ultimate Technology 600 POS manual A4xxxx-xxxxCR, A5xCxDxCR, Clicked Command, A6xCR

Page 49

Table 5. Remote Programming Mode Commands

OP CODE	MNEMONIC/DESCRIPTION		COMMAND/ACKNOWLEDGEMENT
(HEX)

A4	NOTES	COMMAND:		A4xxxx-xxxx<CR>
	Used to enter up to 40 characters of notes	A4	= Op Code
	into RAM. Useful for recording keyboard	xx	= Note (max of 40 Characters)
	version and date, etc.	<CR>	= terminate command (0D hex)
		ACKNOWLEDGEMENT: NONE

A5	SPCDEF	COMMAND:		A5xCxDx<CR>
	Define where SHIFT, CONTROL, and	A5	= Op Code
	ALTERNATE keys are located on auxiliary	x	= 1 right shift
	keyboard.		= 2 left shift
			= 3 right control
			= 4 left control
			= 5 right alternate
			= 6 left alternate
		Cx	= key number
			(refer to Appendix D)
		Dx	= key number
			(refer to Appendix D)
		<CR>	= terminate command (0D hex)
		ACKNOWLEDGEMENT: NONE

A6	CLICKED	COMMAND:		A6x<CR>
	Turns keyboard key audible click on or off.	A6	= Op Code
		x	0 = off
			1 = on
		<CR>	= terminate command (0D hex)
		ACKNOWLEDGEMENT: NONE

Series 600 POS Keyboard

44

Image 49

Contents Programming & USER’S Guide Table of Contents Maintenance List of Tables AppendixList of Figures Series 600 POS Keyboard Special Note ScopeSeries 600 POS Keyboard Product Information FeaturesModel Description BUILT-IN Annunciator BUILT-IN DiagnosticsSpecifications Service and WarrantyWeight Approvals EnvironmentUnpacking and Inspection InstallationCash Drawer Jumper Connections Printer Fired External ConnectionsPrinter 1, 2 Pinouts Driver 1Main RS232 Typical Keyboard External Connections Description Keyboard External Connectors Rear ViewOperation Controls and IndicatorsSeries 600 POS Keyboard Programming Local Mode Programming InstructionsProgramming Keyboard Operating Parameters LED 2 flashes LED 2 turns onLED 2 stops flashing LED 2 turns off Local Mode Programming Instructions = Default Settings Local Mode Programming Instructions = Default Settings List below to select MSR data from one or both good tracks 21 or 20 or23 or 22 or25 or 24 or26 or Turns Series 600 POS Keyboard Cash Drawer Status Local Mode Programming Instructions = Default Settings Numeric keypad, enter Function Code 80 or Define Left Shift Alternate Local Mode Programming Instructions = Default Settings Function Parameter Default Remarks Code Function Parameter Default Remarks Code Setting Function Parameter Default Remarks Code Setting Executed Local Mode programming Function Codes and Default Settings Swiping the Programmers card Break Series Keyboard Description Numeric Keypad noExample Example Programming in Remote Mode Series 600 POS Keyboard Acknowledgement None Command A0krcCxDx.......CRCommand A1aCxDx.......CR Commp Command A4xxxx-xxxxCR Clicked CommandA5xCxDxCR A6xCRNvbdclr Command A9CLRCR Nvbdwr CommandCdsecopn Comment Command Secure CommandADxCR AExCRCommand B0LxCR B2p...........CR B1pdCRCommand B5RSTCR Commit CommandKssnd Command Msrsnd Command OP Code MNEMONIC/DESCRIPTION COMMAND/ACKNOWLEDGEMENT HEXCarded Command BApCR Cdcont CommandBBpCR BCpCR Porte CommandAcknowledgement BDpxCR101/102-KEY Keyboard KEY Code Identification Command BfcrBEnnnnnvvvvkkkkx-xCR BF...............CRRemote Programming KEY MAKE/BREAK Codes Remote Description Programming CommandExamples of Remote Programming for KEY MAKE/BREAK Code Where A0Example Example Opos Opos ProgrammingTrack MSR Programming for UTC Opos DriversPrefix SuffixMSR Source Unit Destination Unit Copying Keyboard Setup Data CloningSeries 500 Main SeriesSystem LOG Operators and Programmers Magnetic CardsPrecautions MaintenanceCleaning KEY Legend Change Inch Full Travel Keyboards Battery ReplacementSeries 600 POS Keyboard Appendix a Series 600 POS Standard Keyboard Layouts Series 600 POS Standard Keyboard Layouts Appendix aBack Connector Pinouts Appendix B Keyboard CABLE/CONNECTOR DataDLE Appendix C Ascii Character SETDecimal Hexadecimal Scan Code KEY Number2B/AB Scan Code KEY Number 4F/CF 3B/BB E1 14 77 E1 62/F0 9D C5 F0 14 F0 VICTOR, NEW York Ultimate Technology Corporation