Ultimate Technology 600 POS manual Example

Page 42

EXAMPLE 1.

This example sequence programs a “shift” key.

1.Place the Series 600 Keyboard in local programming mode by swiping Program Card.

2.At the Series 600 Keyboard numeric keypad, enter 00 or 01.

3.At the Series 600 Keyboard, press the key to be programmed.

4.At the auxiliary keyboard, press and hold the "Shift" key.

5.At the Series 600 Keyboard numeric keypad, enter 1.

6.At the auxiliary keyboard, release the "Shift" key.

7.At the Series 600 Keyboard, press ENTER to complete programming of the key.

8.Repeat steps 3 through 7 to program another key.

9.To exit the programming mode, enter 00 99 at the Series 600 Keyboard numeric keypad. EXAMPLE 2.

This example programs the Series 600 Keyboard to start repeat mode of key using the "A" key.

1.Place the Series 600 Keyboard in local programming mode by swiping the Program Card.

2.At the Series 600 Keyboard numeric keypad, enter 00 or 01.

3.At the Series 600 Keyboard, press the "A" key.

4.At the auxiliary keyboard, press and hold the “A” key.

5.At the Series 600 Keyboard numeric keypad, enter 2.

6.At the auxiliary keyboard, release the “A” key.

7.At the Series 600 Keyboard, press ENTER to complete programming of the key.

8.Repeat steps 3 through 7 to program another key.

9.To exit the programming mode, enter 00 99 at the Series 600 Keyboard numeric keypad.

Series 600 POS Keyboard

37

Image 42

Contents Programming & USER’S Guide Table of Contents Maintenance Appendix List of TablesList of Figures Series 600 POS Keyboard Scope Special NoteSeries 600 POS Keyboard Features Product InformationModel Description BUILT-IN Diagnostics BUILT-IN AnnunciatorWeight Approvals Service and WarrantySpecifications EnvironmentInstallation Unpacking and InspectionPrinter 1, 2 Pinouts External ConnectionsCash Drawer Jumper Connections Printer Fired Driver 1Main RS232 Typical Keyboard External Connections Keyboard External Connectors Rear View DescriptionControls and Indicators OperationSeries 600 POS Keyboard Local Mode Programming Instructions ProgrammingProgramming Keyboard Operating Parameters LED 2 turns on LED 2 flashesLED 2 stops flashing LED 2 turns off Local Mode Programming Instructions = Default Settings Local Mode Programming Instructions = Default Settings List below to select MSR data from one or both good tracks 20 or 21 or22 or 23 or24 or 25 or26 or Turns Series 600 POS Keyboard Cash Drawer Status Local Mode Programming Instructions = Default Settings Numeric keypad, enter Function Code 80 or Define Left Shift Alternate Local Mode Programming Instructions = Default Settings Function Parameter Default Remarks Code Function Parameter Default Remarks Code Setting Function Parameter Default Remarks Code Setting Executed Local Mode programming Function Codes and Default Settings Swiping the Programmers card Series Keyboard Description Numeric Keypad no BreakExample Example Programming in Remote Mode Series 600 POS Keyboard Command A0krcCxDx.......CR Acknowledgement NoneCommand A1aCxDx.......CR Commp Command A5xCxDxCR Clicked CommandA4xxxx-xxxxCR A6xCRNvbdwr Command Nvbdclr Command A9CLRCRCdsecopn ADxCR Secure CommandComment Command AExCRCommand B0LxCR B1pdCR B2p...........CRCommit Command Command B5RSTCRKssnd Command OP Code MNEMONIC/DESCRIPTION COMMAND/ACKNOWLEDGEMENT HEX Msrsnd CommandCarded Command Cdcont Command BApCRBBpCR Acknowledgement Porte CommandBCpCR BDpxCRBEnnnnnvvvvkkkkx-xCR Command Bfcr101/102-KEY Keyboard KEY Code Identification BF...............CRRemote Description Programming Command Remote Programming KEY MAKE/BREAK CodesWhere A0 Examples of Remote Programming for KEY MAKE/BREAK CodeExample Example Opos Programming OposPrefix MSR Programming for UTC Opos DriversTrack SuffixMSR Series 500 Main Copying Keyboard Setup Data CloningSource Unit Destination Unit SeriesOperators and Programmers Magnetic Cards System LOGMaintenance PrecautionsCleaning Battery Replacement KEY Legend Change Inch Full Travel KeyboardsSeries 600 POS Keyboard Appendix a Series 600 POS Standard Keyboard Layouts Appendix a Series 600 POS Standard Keyboard LayoutsAppendix B Keyboard CABLE/CONNECTOR Data Back Connector PinoutsAppendix C Ascii Character SET DLEScan Code KEY Number Decimal Hexadecimal2B/AB Scan Code KEY Number 4F/CF 3B/BB E1 14 77 E1 62/F0 9D C5 F0 14 F0 Ultimate Technology Corporation VICTOR, NEW York