Ultimate Technology 600 POS manual OP Code MNEMONIC/DESCRIPTION COMMAND/ACKNOWLEDGEMENT HEX

Page 55

Table 5. Remote Programming Mode Commands

OP CODE	MNEMONIC/DESCRIPTION		COMMAND/ACKNOWLEDGEMENT
(HEX)

B7	KSSTATUS	COMMAND:		B7<CR>
	Send keyswitch MAKE/BREAK codes in	B7	= Op Code
	current keyswitch 1, 2 or 3 position.	<CR>	= terminate command (0D hex)
		ACKNOWLEDGEMENT: NONE

B8	MSRSND	COMMAND:		B8x<CR>
	Use to send magnetic card reader track	B8	= Op Code
	data for any one good track or if both	x	A = send any good track
	tracks are good.		B = send if both tracks are good
		<CR>	= terminate command (0D hex)
		ACKNOWLEDGEMENT: NONE

B9	CARDED	COMMAND:		B9c<CR>
	Enables or disables tracks on magnetic	B9	= Op Code
	card reader.	c	= track selection
		<CR>	= terminate command (0D hex)
		Track selection:
		A	= track 1 on
		B	= track 2 on
		C	= track 3 on
		D	= track 1 and 2 on
		E	= track 2 and 3 on
		F	= all tracks off
		I	= OPOS track 1 and 2 on
		J	= OPOS track 2 and 3 on
		ACKNOWLEDGEMENT: NONE

Series 600 POS Keyboard

50

Image 55

Contents Programming & USER’S Guide Table of Contents Maintenance List of Tables AppendixList of Figures Series 600 POS Keyboard Special Note ScopeSeries 600 POS Keyboard Product Information FeaturesModel Description BUILT-IN Annunciator BUILT-IN DiagnosticsEnvironment Service and WarrantySpecifications Weight ApprovalsUnpacking and Inspection InstallationDriver 1 External ConnectionsCash Drawer Jumper Connections Printer Fired Printer 1, 2 PinoutsMain RS232 Typical Keyboard External Connections Description Keyboard External Connectors Rear ViewOperation Controls and IndicatorsSeries 600 POS Keyboard Programming Local Mode Programming InstructionsProgramming Keyboard Operating Parameters LED 2 flashes LED 2 turns onLED 2 stops flashing LED 2 turns off Local Mode Programming Instructions = Default Settings Local Mode Programming Instructions = Default Settings List below to select MSR data from one or both good tracks 21 or 20 or23 or 22 or25 or 24 or26 or Turns Series 600 POS Keyboard Cash Drawer Status Local Mode Programming Instructions = Default Settings Numeric keypad, enter Function Code 80 or Define Left Shift Alternate Local Mode Programming Instructions = Default Settings Function Parameter Default Remarks Code Function Parameter Default Remarks Code Setting Function Parameter Default Remarks Code Setting Executed Local Mode programming Function Codes and Default Settings Swiping the Programmers card Break Series Keyboard Description Numeric Keypad noExample Example Programming in Remote Mode Series 600 POS Keyboard Acknowledgement None Command A0krcCxDx.......CRCommand A1aCxDx.......CR Commp Command A6xCR Clicked CommandA4xxxx-xxxxCR A5xCxDxCRNvbdclr Command A9CLRCR Nvbdwr CommandCdsecopn AExCR Secure CommandComment Command ADxCRCommand B0LxCR B2p...........CR B1pdCRCommand B5RSTCR Commit CommandKssnd Command Msrsnd Command OP Code MNEMONIC/DESCRIPTION COMMAND/ACKNOWLEDGEMENT HEXCarded Command BApCR Cdcont CommandBBpCR BDpxCR Porte CommandBCpCR AcknowledgementBF...............CR Command Bfcr101/102-KEY Keyboard KEY Code Identification BEnnnnnvvvvkkkkx-xCRRemote Programming KEY MAKE/BREAK Codes Remote Description Programming CommandExamples of Remote Programming for KEY MAKE/BREAK Code Where A0Example Example Opos Opos ProgrammingSuffix MSR Programming for UTC Opos DriversTrack PrefixMSR Series Copying Keyboard Setup Data CloningSource Unit Destination Unit Series 500 MainSystem LOG Operators and Programmers Magnetic CardsPrecautions MaintenanceCleaning KEY Legend Change Inch Full Travel Keyboards Battery ReplacementSeries 600 POS Keyboard Appendix a Series 600 POS Standard Keyboard Layouts Series 600 POS Standard Keyboard Layouts Appendix aBack Connector Pinouts Appendix B Keyboard CABLE/CONNECTOR DataDLE Appendix C Ascii Character SETDecimal Hexadecimal Scan Code KEY Number2B/AB Scan Code KEY Number 4F/CF 3B/BB E1 14 77 E1 62/F0 9D C5 F0 14 F0 VICTOR, NEW York Ultimate Technology Corporation