Ultimate Technology 600 POS manual 26 or

Page 27

Table 2. Local Mode Programming Instructions

* = Default Settings

Function Code(s)	Operation	Normal Indication	Remarks

26 or 36	1. Swipe	Program Card. While in programming	mode, at the Series 600 Keyboard
Comm (RS232)	numeric keypad, enter applicable Function Code 26 (Port 0) or 36 (Port 1).
Main Port 0 (26)	LED (2) flashes.
AUX Port 1 (36)	LED (2) flashes.
AUX Port 1 (36)
Suffix	2. At the auxiliary keyboard, press the desired key or type the desired key sequence.

	Note that the maximum number of key codes is limited to 24 – this is equivalent to
	approximately 12 key strokes.
			If the Series 600 Keyboard beeps and
			LED (2) turns off while entering key
			codes at the auxiliary keyboard, you
			have exceeded 24 key codes.
			Repeat steps 1 and 2.

3.At the Series 600 Keyboard, press ENTER.

LED (2) turns off.

4.Program the next function code or exit programming mode by entering 99 on Series 600 Keyboard numeric keypad or by swiping the Program Card.

Series 600 POS Keyboard

22

Image 27

Contents Programming & USER’S Guide Table of Contents Maintenance Appendix List of TablesList of Figures Series 600 POS Keyboard Special Note ScopeSeries 600 POS Keyboard Features Product InformationModel Description BUILT-IN Annunciator BUILT-IN DiagnosticsEnvironment Service and WarrantySpecifications Weight ApprovalsUnpacking and Inspection InstallationDriver 1 External ConnectionsCash Drawer Jumper Connections Printer Fired Printer 1, 2 PinoutsMain RS232 Typical Keyboard External Connections Description Keyboard External Connectors Rear ViewOperation Controls and IndicatorsSeries 600 POS Keyboard Local Mode Programming Instructions ProgrammingProgramming Keyboard Operating Parameters LED 2 turns on LED 2 flashesLED 2 stops flashing LED 2 turns off Local Mode Programming Instructions = Default Settings Local Mode Programming Instructions = Default Settings List below to select MSR data from one or both good tracks 21 or 20 or23 or 22 or25 or 24 or26 or Turns Series 600 POS Keyboard Cash Drawer Status Local Mode Programming Instructions = Default Settings Numeric keypad, enter Function Code 80 or Define Left Shift Alternate Local Mode Programming Instructions = Default Settings Function Parameter Default Remarks Code Function Parameter Default Remarks Code Setting Function Parameter Default Remarks Code Setting Executed Local Mode programming Function Codes and Default Settings Swiping the Programmers card Break Series Keyboard Description Numeric Keypad noExample Example Programming in Remote Mode Series 600 POS Keyboard Acknowledgement None Command A0krcCxDx.......CRCommand A1aCxDx.......CR Commp Command A6xCR Clicked CommandA4xxxx-xxxxCR A5xCxDxCRNvbdwr Command Nvbdclr Command A9CLRCRCdsecopn AExCR Secure CommandComment Command ADxCRCommand B0LxCR B2p...........CR B1pdCRCommit Command Command B5RSTCRKssnd Command OP Code MNEMONIC/DESCRIPTION COMMAND/ACKNOWLEDGEMENT HEX Msrsnd CommandCarded Command Cdcont Command BApCRBBpCR BDpxCR Porte CommandBCpCR AcknowledgementBF...............CR Command Bfcr101/102-KEY Keyboard KEY Code Identification BEnnnnnvvvvkkkkx-xCRRemote Programming KEY MAKE/BREAK Codes Remote Description Programming CommandExamples of Remote Programming for KEY MAKE/BREAK Code Where A0Example Example Opos Opos ProgrammingSuffix MSR Programming for UTC Opos DriversTrack PrefixMSR Series Copying Keyboard Setup Data CloningSource Unit Destination Unit Series 500 MainSystem LOG Operators and Programmers Magnetic CardsMaintenance PrecautionsCleaning KEY Legend Change Inch Full Travel Keyboards Battery ReplacementSeries 600 POS Keyboard Appendix a Series 600 POS Standard Keyboard Layouts Series 600 POS Standard Keyboard Layouts Appendix aBack Connector Pinouts Appendix B Keyboard CABLE/CONNECTOR DataDLE Appendix C Ascii Character SETDecimal Hexadecimal Scan Code KEY Number2B/AB Scan Code KEY Number 4F/CF 3B/BB E1 14 77 E1 62/F0 9D C5 F0 14 F0 VICTOR, NEW York Ultimate Technology Corporation