Ultimate Technology 600 POS manual Local Mode Programming Instructions = Default Settings

Page 21

Table 2. Local Mode Programming Instructions

* = Default Settings

	Function Code(s)	Operation		Normal Indication		Remarks

	08	1.	Swipe	Program Card. While in programming mode, at the Series 600 Keyboard
	Enable/Disable		numeric keypad, enter Function Code 08.
	Enable/Disable
	Magnetic Stripe		LED (2) turns on.
	Reader (MSR)	2. At the Series 600 Keyboard numeric keypad, enter the applicable number (1 through
	Tracks
	Tracks		7) to select the MSR track configuration per list below.
			7) to select the MSR track configuration per list below.
				1	= Track 1 enabled only
				2	= Track 2 enabled only
				3	= Track 3 enabled only
				4	= Tracks 1 and 2 enabled *
				5	= Tracks 2 and 3 enabled
				6	= All tracks disabled
				7	= OPOS mode tracks 1 and 2
			LED (2) turns off.
		3. Program the next function code or exit the local programming mode by entering 99 on
			Series 600 Keyboard numeric keypad or by swiping the Program Card.
		Note: Disabling all format tracks will not disable the SECURE or PROGRM cards.

	09	1.	Swipe	Program Card. While in programming mode, at the Series 600 Keyboard
	Magnetic Stripe		numeric keypad, enter Function Code 09.
	Magnetic Stripe
	Reader (MSR)		LED (2) turns on.
	Beeper	2. At the Series 600 Keyboard numeric keypad, enter the applicable number (1 through

			4) to select the magnetic stripe reader beeper operation per list below.
				1	= beep on good read for all enabled tracks
				2	= beep on bad read for all enabled tracks
				3	= beep on good or bad read of enabled tracks*
				4	= no beep on good or bad reads
			LED (2) turns off.
		3.	Program the next function code or exit the local programming mode by entering 99 on
			Series 600 Keyboard numeric keypad followed by ENTER or by swiping the Program
			Card.

Series 600 POS Keyboard

16

Image 21

Contents Programming & USER’S Guide Table of Contents Maintenance Appendix List of TablesList of Figures Series 600 POS Keyboard Special Note ScopeSeries 600 POS Keyboard Features Product InformationModel Description BUILT-IN Annunciator BUILT-IN DiagnosticsSpecifications Service and WarrantyWeight Approvals EnvironmentUnpacking and Inspection InstallationCash Drawer Jumper Connections Printer Fired External ConnectionsPrinter 1, 2 Pinouts Driver 1Main RS232 Typical Keyboard External Connections Description Keyboard External Connectors Rear ViewOperation Controls and IndicatorsSeries 600 POS Keyboard Local Mode Programming Instructions ProgrammingProgramming Keyboard Operating Parameters LED 2 turns on LED 2 flashesLED 2 stops flashing LED 2 turns off Local Mode Programming Instructions = Default Settings Local Mode Programming Instructions = Default Settings List below to select MSR data from one or both good tracks 21 or 20 or23 or 22 or25 or 24 or26 or Turns Series 600 POS Keyboard Cash Drawer Status Local Mode Programming Instructions = Default Settings Numeric keypad, enter Function Code 80 or Define Left Shift Alternate Local Mode Programming Instructions = Default Settings Function Parameter Default Remarks Code Function Parameter Default Remarks Code Setting Function Parameter Default Remarks Code Setting Executed Local Mode programming Function Codes and Default Settings Swiping the Programmers card Break Series Keyboard Description Numeric Keypad noExample Example Programming in Remote Mode Series 600 POS Keyboard Acknowledgement None Command A0krcCxDx.......CRCommand A1aCxDx.......CR Commp Command A4xxxx-xxxxCR Clicked CommandA5xCxDxCR A6xCRNvbdwr Command Nvbdclr Command A9CLRCRCdsecopn Comment Command Secure CommandADxCR AExCRCommand B0LxCR B2p...........CR B1pdCRCommit Command Command B5RSTCRKssnd Command OP Code MNEMONIC/DESCRIPTION COMMAND/ACKNOWLEDGEMENT HEX Msrsnd CommandCarded Command Cdcont Command BApCRBBpCR BCpCR Porte CommandAcknowledgement BDpxCR101/102-KEY Keyboard KEY Code Identification Command BfcrBEnnnnnvvvvkkkkx-xCR BF...............CRRemote Programming KEY MAKE/BREAK Codes Remote Description Programming CommandExamples of Remote Programming for KEY MAKE/BREAK Code Where A0Example Example Opos Opos ProgrammingTrack MSR Programming for UTC Opos DriversPrefix SuffixMSR Source Unit Destination Unit Copying Keyboard Setup Data CloningSeries 500 Main SeriesSystem LOG Operators and Programmers Magnetic CardsMaintenance PrecautionsCleaning KEY Legend Change Inch Full Travel Keyboards Battery ReplacementSeries 600 POS Keyboard Appendix a Series 600 POS Standard Keyboard Layouts Series 600 POS Standard Keyboard Layouts Appendix aBack Connector Pinouts Appendix B Keyboard CABLE/CONNECTOR DataDLE Appendix C Ascii Character SETDecimal Hexadecimal Scan Code KEY Number2B/AB Scan Code KEY Number 4F/CF 3B/BB E1 14 77 E1 62/F0 9D C5 F0 14 F0 VICTOR, NEW York Ultimate Technology Corporation