Ultimate Technology 600 POS manual Local Mode Programming Instructions = Default Settings

Page 34

Table 2. Local Mode Programming Instructions

* = Default Settings

Function Code(s)	Operation		Normal Indication		Remarks

96	1.	Swipe Program	Card.	While in programming mode, at the Series 600 Keyboard
96		numeric keypad, enter Function Code 96.
Set Secure Mode		numeric keypad, enter Function Code 96.
Set Secure Mode
		LED (2) turns on.
	2.	At Series 600 Keyboard numeric keypad, enter the applicable number (0 or 1) to
		select override secure mode of operation per list below.
		0 = not secure
		1 = secure
		LED (2) turns off.
	3.	Program the next function code or exit programming mode by entering 99 on Series
		600 Keyboard numeric keypad or by swiping the Program Card.

97	1.	Swipe Program	Card.	While in programming mode,	at the Series 600 Keyboard
97		numeric keypad, enter Function Code 97.
Default Keyboard		numeric keypad, enter Function Code 97.
Default Keyboard
		LED (2) turns on.
	2.	At Series 600 Keyboard numeric keypad, enter the applicable number (0 or 1) to
		select mode of default operation per list below. Note selection of 1 below resets the
		Series 600 Keyboard to all programmed default key and port settings.
		0 = Exit default mode
		1 = Default mode
	3.	Program the next function code or exit programming mode by entering 99 on Series
		600 Keyboard numeric keypad or by swiping the program Card.

99	Used to terminate the programming mode. When activated, causes all programmed
Exit Program Mode	changes to be saved into non-volatile RAM and the keyboard to do a warm boot. Exiting
	programming mode can also be accomplished b swiping the Program Card.

Series 600 POS Keyboard

29

Image 34

Contents Programming & USER’S Guide Table of Contents Maintenance List of Tables AppendixList of Figures Series 600 POS Keyboard Scope Special NoteSeries 600 POS Keyboard Product Information FeaturesModel Description BUILT-IN Diagnostics BUILT-IN AnnunciatorWeight Approvals Service and WarrantySpecifications EnvironmentInstallation Unpacking and InspectionPrinter 1, 2 Pinouts External ConnectionsCash Drawer Jumper Connections Printer Fired Driver 1Main RS232 Typical Keyboard External Connections Keyboard External Connectors Rear View DescriptionControls and Indicators OperationSeries 600 POS Keyboard Programming Local Mode Programming InstructionsProgramming Keyboard Operating Parameters LED 2 flashes LED 2 turns onLED 2 stops flashing LED 2 turns off Local Mode Programming Instructions = Default Settings Local Mode Programming Instructions = Default Settings List below to select MSR data from one or both good tracks 20 or 21 or22 or 23 or24 or 25 or26 or Turns Series 600 POS Keyboard Cash Drawer Status Local Mode Programming Instructions = Default Settings Numeric keypad, enter Function Code 80 or Define Left Shift Alternate Local Mode Programming Instructions = Default Settings Function Parameter Default Remarks Code Function Parameter Default Remarks Code Setting Function Parameter Default Remarks Code Setting Executed Local Mode programming Function Codes and Default Settings Swiping the Programmers card Series Keyboard Description Numeric Keypad no BreakExample Example Programming in Remote Mode Series 600 POS Keyboard Command A0krcCxDx.......CR Acknowledgement NoneCommand A1aCxDx.......CR Commp Command A5xCxDxCR Clicked CommandA4xxxx-xxxxCR A6xCRNvbdclr Command A9CLRCR Nvbdwr CommandCdsecopn ADxCR Secure CommandComment Command AExCRCommand B0LxCR B1pdCR B2p...........CRCommand B5RSTCR Commit CommandKssnd Command Msrsnd Command OP Code MNEMONIC/DESCRIPTION COMMAND/ACKNOWLEDGEMENT HEXCarded Command BApCR Cdcont CommandBBpCR Acknowledgement Porte CommandBCpCR BDpxCRBEnnnnnvvvvkkkkx-xCR Command Bfcr101/102-KEY Keyboard KEY Code Identification BF...............CRRemote Description Programming Command Remote Programming KEY MAKE/BREAK CodesWhere A0 Examples of Remote Programming for KEY MAKE/BREAK CodeExample Example Opos Programming OposPrefix MSR Programming for UTC Opos DriversTrack SuffixMSR Series 500 Main Copying Keyboard Setup Data CloningSource Unit Destination Unit SeriesOperators and Programmers Magnetic Cards System LOGPrecautions MaintenanceCleaning Battery Replacement KEY Legend Change Inch Full Travel KeyboardsSeries 600 POS Keyboard Appendix a Series 600 POS Standard Keyboard Layouts Appendix a Series 600 POS Standard Keyboard LayoutsAppendix B Keyboard CABLE/CONNECTOR Data Back Connector PinoutsAppendix C Ascii Character SET DLEScan Code KEY Number Decimal Hexadecimal2B/AB Scan Code KEY Number 4F/CF 3B/BB E1 14 77 E1 62/F0 9D C5 F0 14 F0 Ultimate Technology Corporation VICTOR, NEW York