Thomas & Betts Limitorque MX Device Net Field Unit manual View DeviceNet Status, View Settings

Page 36

Limitorque MX DeviceNet Field Unit FCD LMENIM2328-00 – 11/05

4.6.2View Settings

Refer to Bulletin LMAIM1306/2306, MX Installation and Operation Manual to access the “VIEW SETTINGS” menu. Verify the settings as follows:

5 View DeviceNet Status

Figure 5.1 – DeviceNet Screens

YES

YES

YES

YES

YES

YES

YES

YES

CHANGE

STATUS

BAUD RATE

DNET ADDRESS

ANALOG SCALE

CHANGE PROP

PROP BAND

DEADBAND

DEVICENET?

(OFF)-OK?

AUTO-OK?

NET CTRL-OK?

(0-100)-OK

DEAD BAND?

(8%)-OK?

(2%)

NO

(ON)

NO

(125K)

NO

(0-63)

NO

(0-255)

NO

NO

(1-100%)

NO

(1-?%)

NO

(250K)

(0-4095)

(500K)

(NET CTRL)

		YES				YES					YES
ESD ACTION					COMM LOSS ACTION					COMM LOSS DELAY
(IGNORE)-OK?					(NONE)-OK?					(60 SEC)-OK?
	NO	*		YES		NO	*		YES		NO
(CLOSE)	NO	*			(CLOSE)	NO	*			(0-4095)	NO
(CLOSE)					(CLOSE)					(0-4095)
(OPEN)			MOVE TO		(OPEN)			MOVE TO
(STOP)			MOVE TO		(STOP)			MOVE TO
(POSITION)			XXX% OPEN		(POSITION)			XXX% OPEN
			(0-100%)	NO				(0-100%)	NO
			(0-100%)					(0-100%)

*If POSITION is chosen, as action, this menu will appear.

36

VIEW DNET STATUS?

This selection permits the User to view pertinent information which summarizes the status of the DeviceNet option board.

VIEW MODULE STATUS?

• Answer "YES" to determine status of individual DN board within the actuator.

• Configuration choices are:

• "OFF" = board installed but turned off

• “OPERATIONAL” – The device is operating in a normal condition.

• "STANDBY" = The device needs commissioning due to configuration missing, incomplete or incorrect.

• "RECOVERABLE FAULT" = Conditions that can cause this event are e.g. communication fault, power fault or Limigard fault of the SMT Main Board. Device may need resetting.

• "UNRECOVERABLE FAULT" = Internal Diagnostic Fault detected e.g.

• Receive Queue Overrun

• Transmit Queue Overrun

• CAN Controller Overrun

• Device may need replacing.

• "SELF TESTING" = The device is in self-test mode.

VIEW NETWORK STATUS?

Answer “YES” to determine status of DN network.

• "NOT ON LINE" = Device is not on-line.

Image 36

Contents User Instructions Disclaimer Contents EDS File Declaration of Conformity to the DeviceNet Specification Declaration of DeviceNet Conformance Odva CertificationAbbreviations Purpose How to Use this Manual User SafetyIntroduction DeviceNet System Capabilities and Features General SpecificationsUser Knowledge Network specifications MX Field Unit SpecificationsSystem Components IntroductionHardware Limitorque MXDeviceNet Field Unit DeviceNet Field UnitBelden Cable Specifications Hardware interfaceNetwork Cable Installation and Configuration Site and Network Cable PreparationSite Preparation Network Cable PreparationCable Preparation Installation Verification Network Cabling Installation VerificationDnfu Installation Verification Object Model Diagram Assembly ObjectsOutput Assembly Instances Output Assembly InstanceClass Instance Attribute Data Name Type Input Assembly Instance 10 Input Assembly Instance 11 Input Assembly InstanceDIPositionandBusModeChan DIPositionChan14 Possible values of DIPositionChan DIActuatorFaults2Chan DIActuatorAlarmsChan16 Possible values of DIActuatorFaults1Chan 18 Possible values of DIActuatorFaults2Chan20 Possible values of DIActuatorAlarmsChan DIDiscUserInputChanDIReadDiscOutputChan DOPositionChanDIActuatorFaults3Chan DIAlarms2ChanDORelayChan CtrlStatusChanBit 7 Bit Reserved Low Battery Channel Interface ObjectName Data Description Type AttributeTransducer Block Object Name Data Type Description Semantics of ValueName Data Type Description Semantics of Value 33 Transducer Attribute Scaled values attribute Bit 7Identity Object Instance Attributes 35 Identity Object Instance AttributesBit 15 Bit 10 Description Semantics of Value AttributeBehavior 36 BehaviorEvent Source Description DeviceNet Object Instance Attributes 37 DeviceNet Object Instance AttributesName Data Description Semantics of Value Type Attribute Discrete Input Point Object Class ID 8 08hex 38 Discrete Input Point ObjectInstance ID Channel Interface Object Source Discrete Output Point Object Class ID 9 09hex Analog Input Point Object Class ID 10 0AhexAnalog Output Point Object Class ID 11 0Bhex 39 Discrete Output Point ObjectNetwork Management MAC IDBaud Rate Offline Connection Set Device Heartbeat MessageConfiguration Confirmation Device Shutdown MessageChecking Connections 43 Format of the Device Shutdown MessageView Settings View DeviceNet StatusChecking the Normal Display Troubleshooting Access Path to ObjectAssociated Documents EDS FileWorkmanship How to Order Parts Regulatory InformationWiring Diagram Limitorque MX DeviceNet Field Unit FCD LMENIM2328-00 11/05 Flowserve.com Flowserve.com