Tannoy ACTIVE STUDIO MONITORS owner manual Master Unit, Slave/Subwoofer

Page 13

Master Unit

1.System controller/slave switch.

In the “out” position the monitor operates as a System Controller.

*There can only be one system Controller in a setup. In the “in” position the monitor operates as a regular master or a slave unit.

2.RJ45 link connectors for downstream slave units, remote and PC control.

3.Analogue Inputs.

4.AES/EBU Digital Input

5.Word Clock BNC Sync

6.Power Input 100-240v and Power ON/Off Switch.

5

Slave/Subwoofer

1.RJ45 Link Connections for downstream slave units, remote and PC control.

2.Power Input 100-240v and power ON/Off Switch.

Optional Digital I/0 Card With this card installed in the master monitor. Analogue input slot a 5.1 Digital/ 6 Master setup becomes an option. Three AES/EBU connections (6ch) can then be fed to one master monitor and distributed downstream. See the”setups” section for further information.

2

1

2

3

4

5

1

13

Image 13

Contents Owners M a N U a L Page Important Safety Instructions Important Safety Instructions Quick Setup Guide T I V E S T U D I O M O N I T O R S Introduction Tannoy Dual Concentric Concept & Design PhilosophyUnpacking & Visual Checks High efficiency compact Switched Mode Power Supply SmpsTannoy WideBand SuperTweeter Preliminary Recommendation Speaker PlacementOrientation Master & Slave Concept Slave Monitor & Subwoofer Remote ControlInitializing the Network IDP Soft Software RemoteSlave/Subwoofer Master UnitSUB IDP Display Master General Setup ProcedureGeneral Setup Procedure SetupsAnalog Stereo Set-up With Mono Subs Stereo Digital Set-up With Mono Subs Analog Stereo Set-up With Stereo SubsDigital Set-up Analog Set-upDigital 192kHz Set-up Digital Set-up Analog Set-up Analog, Digital& 192kHz Alternative 7.1 Set-upConnecting Three Subs Connecting Two SubsStereo Set-up With Chains on L&R. Analog or Digital Dig/6 MasterSetup when the monitors are connected Reset All Settings Reset ProcedureSelect Setup Select Monitor TasksParameter Description Press Enter to access the Select ModeMain Display † PC-iPBass Management PhaseLFE Low Pass Filter LFE GainSetup Setup MenuSet Monitor Task External ClockLFE channel important Parameters available for the subwooferParameter Categories IDP Remote Volume potentiometer Preset 1/3 and 2/4 keysREF Level keys MUTE/UNMUTE Solo keys for the channels R LS- SUB RSInstallation on Mac Installation on PCIDP Soft Minimum requirementsREF LEV. keys Volume ControlMonitor and Sub icons Bass Mgt Bass ManagementRecall presets IDP Soft Preset ListStore presets Locked symbol in Preset ListUpload Software to Monitors IDP Soft NetworkAnalog Gain System Setup ConfigurationBNC Sync Calibrate Main Monitors Monitor AssignmentCalibrate Subwoofer LFE Gain Range 0 to 14dB Phase RangeLFE Low Pass Filter Chained monitors System Master & Slaves Technical Specifications Precision 6 iDPTechnical Specifications- Precision 8 iDP TS112 iDP Subwoofer & iDP Technical Specifications TS212 iDP SubwooferDimensions Precision 6 iDP Dimensions Precision 8 iDP Dimensions Precision TS112 iDP Grey Dimensions Precision TS212 iDP Grey/SilverIDP Display Messages Curves Explained System Delays Sample Rate Digital Input Analog InputSUB LFE TC Link Standard Cat-5 cables CablesAES/EBU Standard cables Serial to Cat-5 cableDeclaration Of Conformity Warranty Page Issue Software Version 1.53 Part No GH 01 December