Tannoy ACTIVE STUDIO MONITORS owner manual Digital Set-up

Page 20

A C T I V E S T U D I O M O N I T O R S

6.1 Digital Set-up

The diagram shows how to connect a 6.1 digital set-up.

All Master monitors require installed digital I/O cards.

AES signal is fed to input 2 of these cards.

The Centre monitor is set as the System Controller by leaving out the TC Link button on the rear panel.

The Centre monitor receives audio for both centre & LFE channels via the AES input connector (input 2). The LFE subwoofer is fed via the RJ-45 connection from the left monitor.

RJ45 Network connections from the Centre monitor to the Left & Right monitors are required.

The Left Monitor receives audio for both Left & LS channels via the AES input connector (input 2). The LS monitor is fed via the RJ-45 connection from the Left monitor. The CS monitor is fed via the RJ-45 connector from the LS monitor. Audio for the CS monitor is fed to input 2.

The Right Monitor receives audio for both Right & RS channels via the AES input connector (input 2). The RS monitor is fed via the RJ-45 connection from the Left monitor.

When no Bass management is selected, only the LFE signal will be sent to the subwoofer.

When Bass management is selected, low frequency content from the 5 main channels is extracted and sent to the subwoofer where it is summed with the LFE channel. (Only LF, Center, RF, LS, and RS contribute to the bass management signal.)

The iDP™ Remote, iDP SOFT™ or PC-iP™can be connected to any spare TC Link “out” connection.

! REMEMBER – To set a master monitor as the system controller the TC Link button on the rear panel MUST be in the out position.

6.1 Digital 192kHz Set-up

The diagram shows how to connect a 6.1 digital set-up at 192khz.

All Master monitors require installed digital I/O cards.

AES signal is fed to inputs 2&3 of these cards.

The Centre monitor is set as the System Controller by leaving out the TC Link button on the rear panel.

The Centre monitor receives audio for both centre & LFE channels

via the AES input connectors (input 2 for Centre & input 3 for Sub). The LFE subwoofer is fed via the RJ-45 connection from the left monitor.

RJ45 Network connections from the Centre monitor to the Left & Right monitors are required.

The Left Monitor receives audio for both Left & LS channels via the AES input connector (input 2 for Left & input 3 for LS).

The LS monitor is fed via the RJ-45 connection from the Left monitor. The CS monitor is fed via the RJ-45 connector from the LS monitor. Audio for the CS monitor is fed to input 2.

The Right Monitor receives audio for both Right & RS channels via the AES input connector (input 2 for Left & input 3 for RS).

The RS monitor is fed via the RJ-45 connection from the Left monitor.

Clock MUST be sent on the AES connection feeding the Centre/LFE channels (or on BNC). When no Bass management is selected, only the LFE signal will be sent to the subwoofer.

When Bass management is selected, low frequency content from the 5 main channels is extracted and sent to the subwoofer where it is summed with the LFE channel. (Only LF, Center, RF, LS, and RS contribute to the bass management signal.)

The iDP™ Remote, iDP SOFT™ or PC-iP™can be connected to any spare TC Link “out” connection.

! REMEMBER – To set a master monitor as the system controller the TC Link button on the rear panel MUST be in the out position.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Owners M a N U a L Page Important Safety Instructions Important Safety Instructions Quick Setup Guide T I V E S T U D I O M O N I T O R S Introduction Concept & Design Philosophy Tannoy Dual ConcentricTannoy WideBand SuperTweeter High efficiency compact Switched Mode Power Supply SmpsUnpacking & Visual Checks Orientation Speaker PlacementPreliminary Recommendation Master & Slave Concept Remote Control Slave Monitor & SubwooferInitializing the Network IDP Soft Software RemoteMaster Unit Slave/SubwooferSUB General Setup Procedure IDP Display MasterAnalog Stereo Set-up With Mono Subs SetupsGeneral Setup Procedure Analog Stereo Set-up With Stereo Subs Stereo Digital Set-up With Mono SubsAnalog Set-up Digital Set-upDigital 192kHz Set-up Digital Set-up Analog Set-up Alternative 7.1 Set-up Analog, Digital& 192kHzConnecting Two Subs Connecting Three SubsDig/6 Master Stereo Set-up With Chains on L&R. Analog or DigitalSetup when the monitors are connected Reset Procedure Reset All SettingsSelect Setup Select Monitor TasksPress Enter to access the Select Mode Parameter DescriptionMain Display † PC-iPPhase Bass ManagementLFE Low Pass Filter LFE GainSetup Menu SetupSet Monitor Task External ClockParameters available for the subwoofer LFE channel importantParameter Categories IDP Remote Preset 1/3 and 2/4 keys Volume potentiometerREF Level keys MUTE/UNMUTE Solo keys for the channels R LS- SUB RSInstallation on PC Installation on MacIDP Soft Minimum requirementsVolume Control REF LEV. keysMonitor and Sub icons Bass Mgt Bass ManagementIDP Soft Preset List Recall presetsStore presets Locked symbol in Preset ListIDP Soft Network Upload Software to MonitorsBNC Sync System Setup ConfigurationAnalog Gain Monitor Assignment Calibrate Main MonitorsCalibrate Subwoofer LFE Low Pass Filter Phase RangeLFE Gain Range 0 to 14dB Chained monitors Technical Specifications Precision 6 iDP System Master & SlavesTechnical Specifications- Precision 8 iDP Technical Specifications TS212 iDP Subwoofer TS112 iDP Subwoofer & iDPDimensions Precision 6 iDP Dimensions Precision 8 iDP Dimensions Precision TS212 iDP Grey/Silver Dimensions Precision TS112 iDP GreyIDP Display Messages System Delays Sample Rate Digital Input Analog Input Curves ExplainedSUB LFE Cables TC Link Standard Cat-5 cablesAES/EBU Standard cables Serial to Cat-5 cableDeclaration Of Conformity Warranty Page Issue Software Version 1.53 Part No GH 01 December
Top Page Image Contents