Tannoy ACTIVE STUDIO MONITORS owner manual Analog Set-up, Digital Set-up

Page 18

A C T I V E S T U D I O M O N I T O R S

5.1 Analog Set-up

The diagram shows how to connect a 5.1 analog set-up.

The Centre monitor is set as the System Controller by leaving out the TC Link button on the rear panel.

The Centre monitor receives audio for both centre (input 1) & LFE channels (input 2) via the analog input connectors. The LFE subwoofer is fed via the RJ-45 connection from the left monitor.

RJ45 Network connections from the Centre monitor to the Left & Right monitors are required.

The Left Monitor receives audio for both Left (input 1) & LS channels (input 2) via the analog input connectors. The LS monitor is fed via the RJ-45 connection from the Left monitor.

The Right Monitor receives audio for both Right (input 1) & RS channels (input 2) via the analog input connectors. The RS monitor is fed via the RJ-45 connection from the Right monitor.

When no Bass management is selected, only the LFE signal will be sent to the subwoofer.

When Bass management is selected, low frequency content from the 5 main channels is extracted and sent to the subwoofer where it is summed with the LFE channel

The iDP™ Remote, iDP SOFT™ or PC-iP™can be connected to any spare TC Link “out” connection.

! REMEMBER – To set a master monitor as the system controller the TC Link button on the rear panel MUST be in the out position.

5.1 Digital Set-up

The diagram shows how to connect a 5.1 digital set-up.

All Master monitors require installed digital I/O cards.

AES signal is fed to input 2 of these cards.

The Centre monitor is set as the System Controller by leaving out the TC Link button on the rear panel.

The Centre monitor receives audio for both centre & LFE channels via the AES input connector (input 2). The LFE subwoofer is fed via the RJ-45 connection from the left monitor.

RJ45 Network connections from the Centre monitor to the Left & Right monitors are required.

The Left Monitor receives audio for both Left & LS channels via the AES input connector (input 2). The LS monitor is fed via the RJ-45 connection from the Left monitor.

The Right Monitor receives audio for both Right & RS channels via the AES input connector (input 2). The RS monitor is fed via the RJ-45 connection from the Left monitor.

When no Bass management is selected, only the LFE signal will be sent to the subwoofer.

When Bass management is selected, low frequency content from the

5 main channels is extracted and sent to the subwoofer where it is summed with the LFE channel The iDP™ Remote, iDP SOFT™ or PC-iP™can be connected to any spare TC Link “out” connection.

! REMEMBER – To set a master monitor as the system controller the TC Link button on the rear panel MUST be in the out position.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Owners M a N U a L Page Important Safety Instructions Important Safety Instructions Quick Setup Guide T I V E S T U D I O M O N I T O R S Introduction Concept & Design Philosophy Tannoy Dual ConcentricHigh efficiency compact Switched Mode Power Supply Smps Unpacking & Visual ChecksTannoy WideBand SuperTweeter Speaker Placement Preliminary RecommendationOrientation Master & Slave Concept Initializing the Network Remote ControlSlave Monitor & Subwoofer IDP Soft Software RemoteMaster Unit Slave/SubwooferSUB General Setup Procedure IDP Display MasterSetups General Setup ProcedureAnalog Stereo Set-up With Mono Subs Analog Stereo Set-up With Stereo Subs Stereo Digital Set-up With Mono SubsAnalog Set-up Digital Set-upDigital 192kHz Set-up Digital Set-up Analog Set-up Alternative 7.1 Set-up Analog, Digital& 192kHzConnecting Two Subs Connecting Three SubsDig/6 Master Stereo Set-up With Chains on L&R. Analog or DigitalSetup when the monitors are connected Select Setup Reset ProcedureReset All Settings Select Monitor TasksMain Display Press Enter to access the Select ModeParameter Description † PC-iPLFE Low Pass Filter PhaseBass Management LFE GainSet Monitor Task Setup MenuSetup External ClockParameters available for the subwoofer LFE channel importantParameter Categories IDP Remote REF Level keys Preset 1/3 and 2/4 keysVolume potentiometer MUTE/UNMUTE Solo keys for the channels R LS- SUB RSIDP Soft Installation on PCInstallation on Mac Minimum requirementsMonitor and Sub icons Volume ControlREF LEV. keys Bass Mgt Bass ManagementStore presets IDP Soft Preset ListRecall presets Locked symbol in Preset ListIDP Soft Network Upload Software to MonitorsSystem Setup Configuration Analog GainBNC Sync Monitor Assignment Calibrate Main MonitorsCalibrate Subwoofer Phase Range LFE Gain Range 0 to 14dBLFE Low Pass Filter Chained monitors Technical Specifications Precision 6 iDP System Master & SlavesTechnical Specifications- Precision 8 iDP Technical Specifications TS212 iDP Subwoofer TS112 iDP Subwoofer & iDPDimensions Precision 6 iDP Dimensions Precision 8 iDP Dimensions Precision TS212 iDP Grey/Silver Dimensions Precision TS112 iDP GreyIDP Display Messages System Delays Sample Rate Digital Input Analog Input Curves ExplainedSUB LFE AES/EBU Standard cables CablesTC Link Standard Cat-5 cables Serial to Cat-5 cableDeclaration Of Conformity Warranty Page Issue Software Version 1.53 Part No GH 01 December
Top Page Image Contents