Tannoy ACTIVE STUDIO MONITORS owner manual IDP Soft Network, Upload Software to Monitors

Page 37

iDP SOFT™ (cont.)

Network

Accessing the Network Screen

Press the ((())) icon in the Main screen to access the Network facilities. In this screen various global network settings are handled.

Press <AutoDetect> to scan your COM ports. If an Precision iDP™ System is connected to any port it will be recognized. Note that the AutoDetect function will not executed until <OK> is pressed.

<Port>

Manual select of Serial/COM port.

<Status>

Indicates the status when entering the Network screen.

<Clear Network> - Clear Setup for entire network

Select this reset procedure to clear all tasks and setup settings.

<Clear Settings> - Clear Monitor Settings

All global and local parameters in connected monitors are reset. Preset and network settings are not affected.

<Reset to Factory Settings> - Reset All Settings

A “factory” reset procedure that deletes all global and local parameter settings as well as preset and network settings.

<Upload Software to Monitors>

Software updates for the Precision iDP™ Monitors comes as (.syx) files There are various files for monitors and subs.

Save the .syx - file to a location on your hard drive prior to the uploading the file.

Disconnect all network cables from the speaker you wish to update and connect your computer to this individual speaker.

Press Upload Software to Monitors

Follow the onscreen instructions

Continue the process of updating one speaker at a time.

Replace the network cables.

Re-assign the appropriate monitor tasks to each speaker in your iDP system.

37

Image 37

Contents Owners M a N U a L Page Important Safety Instructions Important Safety Instructions Quick Setup Guide T I V E S T U D I O M O N I T O R S Introduction Tannoy Dual Concentric Concept & Design PhilosophyUnpacking & Visual Checks High efficiency compact Switched Mode Power Supply SmpsTannoy WideBand SuperTweeter Preliminary Recommendation Speaker PlacementOrientation Master & Slave Concept Slave Monitor & Subwoofer Remote ControlInitializing the Network IDP Soft Software RemoteSlave/Subwoofer Master UnitSUB IDP Display Master General Setup ProcedureGeneral Setup Procedure SetupsAnalog Stereo Set-up With Mono Subs Stereo Digital Set-up With Mono Subs Analog Stereo Set-up With Stereo SubsDigital Set-up Analog Set-upDigital 192kHz Set-up Digital Set-up Analog Set-up Analog, Digital& 192kHz Alternative 7.1 Set-upConnecting Three Subs Connecting Two SubsStereo Set-up With Chains on L&R. Analog or Digital Dig/6 MasterSetup when the monitors are connected Reset All Settings Reset ProcedureSelect Setup Select Monitor TasksParameter Description Press Enter to access the Select ModeMain Display † PC-iPBass Management PhaseLFE Low Pass Filter LFE GainSetup Setup MenuSet Monitor Task External ClockLFE channel important Parameters available for the subwooferParameter Categories IDP Remote Volume potentiometer Preset 1/3 and 2/4 keysREF Level keys MUTE/UNMUTE Solo keys for the channels R LS- SUB RSInstallation on Mac Installation on PCIDP Soft Minimum requirementsREF LEV. keys Volume ControlMonitor and Sub icons Bass Mgt Bass ManagementRecall presets IDP Soft Preset ListStore presets Locked symbol in Preset ListUpload Software to Monitors IDP Soft NetworkAnalog Gain System Setup ConfigurationBNC Sync Calibrate Main Monitors Monitor AssignmentCalibrate Subwoofer LFE Gain Range 0 to 14dB Phase RangeLFE Low Pass Filter Chained monitors System Master & Slaves Technical Specifications Precision 6 iDPTechnical Specifications- Precision 8 iDP TS112 iDP Subwoofer & iDP Technical Specifications TS212 iDP SubwooferDimensions Precision 6 iDP Dimensions Precision 8 iDP Dimensions Precision TS112 iDP Grey Dimensions Precision TS212 iDP Grey/SilverIDP Display Messages Curves Explained System Delays Sample Rate Digital Input Analog InputSUB LFE TC Link Standard Cat-5 cables CablesAES/EBU Standard cables Serial to Cat-5 cableDeclaration Of Conformity Warranty Page Issue Software Version 1.53 Part No GH 01 December