Tannoy ACTIVE STUDIO MONITORS Parameters available for the subwoofer, LFE channel important

Page 30

A C T I V E S T U D I O M O N I T O R S

Parameters available for Precision 6 iDPand Precision 8 iDP:-

Pink Noise

-

On/Off

Calibrate

-

Level calibration of the selected monitor. Range –6dB to +6dB

Rel.Lev.

-

Relative preset volume for the selected monitor relative to the calibrated and global volume.

 

 

Range –40dB to 0dB

Room Position

-

Neutral

 

 

Wall

 

 

Corner

 

 

Console

 

 

C. Wall - Console Wall

 

 

C. Corn - Console Corner

Bass

-

Bass adjustment for the selected monitor. Range –6dB to +6dB

Treble

-

Treble adjustment for the selected monitor. Range –6dB to +6dB

Parameters available for the subwoofer: -

Pink Noise

-

On/Off

Calibrate

-

Level calibration of the selected monitor. Range –18dB to +6dB

Rel.Lev.

-

Relative preset volume for the selected monitor relative to the calibrated and global volume.

 

 

Range –40dB to 0dB

LFE – Low Pass

-

Low pass filter on the LFE channel attenuating frequencies above 120Hz

LFE Gain

-

With this parameter you can boost the acoustic gain of the LFE channel

 

 

Range –6dB to +8dB

Polarity

-

If the Subwoofer is correctly placed, setting the Phase Reverse parameter at 180º should result

 

 

in a full Phase cancellation at the set Crossover frequency. If this is not the case - the Delay

 

 

parameter should be adjusted.

 

 

Range: 0 or 180º

Phase

-

To time-compensate if the Sub is not placed according to the ITU 775 recommendations.

 

 

There are individual Phase settings for each of the Bass Management Crossover frequencies.

 

 

Once set, these are stored as Global settings. Range: 0 to180º

LFE channel - important

Please note that in general the LFE channel should be mixed with +10dB headroom.

If you are not able to boost your LFE monitor output from your console, +10dB gain can be added on your Precision TS112 iDPor TS212 iDPSubwoofer input. Most encoder/ decoder formats take the LFE boost into account, meaning that you should leave the Precision TS112 iDPSubwoofer LFE gain at 0dB when playing back DTS or DOLBY encoded material on your Precision IDP system. LFE gain is set at 0dB in all factory presets, if you need to add gain on your Precision TS112 iDPSubwoofer please adjust this parameter and store the new setting in a user preset location.

30

Image 30
Contents Owners M a N U a L Page Important Safety Instructions Important Safety Instructions Quick Setup Guide T I V E S T U D I O M O N I T O R S Introduction Concept & Design Philosophy Tannoy Dual ConcentricHigh efficiency compact Switched Mode Power Supply Smps Unpacking & Visual ChecksTannoy WideBand SuperTweeter Speaker Placement Preliminary RecommendationOrientation Master & Slave Concept Initializing the Network Remote ControlSlave Monitor & Subwoofer IDP Soft Software RemoteMaster Unit Slave/SubwooferSUB General Setup Procedure IDP Display MasterSetups General Setup ProcedureAnalog Stereo Set-up With Mono Subs Analog Stereo Set-up With Stereo Subs Stereo Digital Set-up With Mono SubsAnalog Set-up Digital Set-upDigital 192kHz Set-up Digital Set-up Analog Set-up Alternative 7.1 Set-up Analog, Digital& 192kHzConnecting Two Subs Connecting Three SubsDig/6 Master Stereo Set-up With Chains on L&R. Analog or DigitalSetup when the monitors are connected Select Setup Reset ProcedureReset All Settings Select Monitor TasksMain Display Press Enter to access the Select ModeParameter Description † PC-iPLFE Low Pass Filter PhaseBass Management LFE GainSet Monitor Task Setup MenuSetup External ClockParameters available for the subwoofer LFE channel importantParameter Categories IDP Remote REF Level keys Preset 1/3 and 2/4 keysVolume potentiometer MUTE/UNMUTE Solo keys for the channels R LS- SUB RSIDP Soft Installation on PCInstallation on Mac Minimum requirementsMonitor and Sub icons Volume ControlREF LEV. keys Bass Mgt Bass ManagementStore presets IDP Soft Preset ListRecall presets Locked symbol in Preset ListIDP Soft Network Upload Software to MonitorsSystem Setup Configuration Analog GainBNC Sync Monitor Assignment Calibrate Main MonitorsCalibrate Subwoofer Phase Range LFE Gain Range 0 to 14dBLFE Low Pass Filter Chained monitors Technical Specifications Precision 6 iDP System Master & SlavesTechnical Specifications- Precision 8 iDP Technical Specifications TS212 iDP Subwoofer TS112 iDP Subwoofer & iDPDimensions Precision 6 iDP Dimensions Precision 8 iDP Dimensions Precision TS212 iDP Grey/Silver Dimensions Precision TS112 iDP GreyIDP Display Messages System Delays Sample Rate Digital Input Analog Input Curves ExplainedSUB LFE AES/EBU Standard cables CablesTC Link Standard Cat-5 cables Serial to Cat-5 cableDeclaration Of Conformity Warranty Page Issue Software Version 1.53 Part No GH 01 December