Tannoy ACTIVE STUDIO MONITORS owner manual Important Safety Instructions

Page 3

4	Important Safety Instructions
5	Quick Set-Up Guide
7	Introduction
8	Concept & Design Philosophy
9	Unpacking & Visual Checks
10	Preliminary Recommendation
10	Monitor Placement
10	Orientation
11	Master & Slave Concept
13	Rear Panel Description
14	Operational Overview
15	iDP™ Display & Setup Procedure
16	Set-Ups
25	Set-Up When The Monitors are connected
27	Parameter Description
28	Bass Management
29	Set-Up Menu
30	® Parameters Available for Precision 6 iDP™ Precision 8 iDP™
30	® Parameters Available for TS112 iDP™ Subwoofer
31	Parameter Categories
32	iDP™ Remote
34	iDP SOFT™
43	Technical Specifications. Precision 6 iDP™
44	Technical Specifications. Precision 8 iDP™
45	Technical Specifications. TS212 iDP™ & TS112 iDP™ Subwoofer & iDP™ Remote
46	Performance Data
47	Dimensions
	Appendix
50	iDP™ Display Messages
51	System Delays
51	X-Curves Explained
52	Preset List
53	iDP™ Cables
54	Declaration of Conformity
55	Warranty

3

Image 3

Contents Owners M a N U a L Page Important Safety Instructions Important Safety Instructions Quick Setup Guide T I V E S T U D I O M O N I T O R S Introduction Tannoy Dual Concentric Concept & Design PhilosophyHigh efficiency compact Switched Mode Power Supply Smps Unpacking & Visual ChecksTannoy WideBand SuperTweeter Speaker Placement Preliminary RecommendationOrientation Master & Slave Concept IDP Soft Software Remote Remote ControlSlave Monitor & Subwoofer Initializing the NetworkSlave/Subwoofer Master UnitSUB IDP Display Master General Setup ProcedureSetups General Setup ProcedureAnalog Stereo Set-up With Mono Subs Stereo Digital Set-up With Mono Subs Analog Stereo Set-up With Stereo SubsDigital Set-up Analog Set-upDigital 192kHz Set-up Digital Set-up Analog Set-up Analog, Digital& 192kHz Alternative 7.1 Set-upConnecting Three Subs Connecting Two SubsStereo Set-up With Chains on L&R. Analog or Digital Dig/6 MasterSetup when the monitors are connected Select Monitor Tasks Reset ProcedureReset All Settings Select Setup† PC-iP Press Enter to access the Select ModeParameter Description Main DisplayLFE Gain PhaseBass Management LFE Low Pass FilterExternal Clock Setup MenuSetup Set Monitor TaskLFE channel important Parameters available for the subwooferParameter Categories IDP Remote MUTE/UNMUTE Solo keys for the channels R LS- SUB RS Preset 1/3 and 2/4 keysVolume potentiometer REF Level keysMinimum requirements Installation on PCInstallation on Mac IDP SoftBass Mgt Bass Management Volume ControlREF LEV. keys Monitor and Sub iconsLocked symbol in Preset List IDP Soft Preset ListRecall presets Store presetsUpload Software to Monitors IDP Soft NetworkSystem Setup Configuration Analog GainBNC Sync Calibrate Main Monitors Monitor AssignmentCalibrate Subwoofer Phase Range LFE Gain Range 0 to 14dBLFE Low Pass Filter Chained monitors System Master & Slaves Technical Specifications Precision 6 iDPTechnical Specifications- Precision 8 iDP TS112 iDP Subwoofer & iDP Technical Specifications TS212 iDP SubwooferDimensions Precision 6 iDP Dimensions Precision 8 iDP Dimensions Precision TS112 iDP Grey Dimensions Precision TS212 iDP Grey/SilverIDP Display Messages Curves Explained System Delays Sample Rate Digital Input Analog InputSUB LFE Serial to Cat-5 cable CablesTC Link Standard Cat-5 cables AES/EBU Standard cablesDeclaration Of Conformity Warranty Page Issue Software Version 1.53 Part No GH 01 December