Tannoy ACTIVE STUDIO MONITORS Cables, TC Link Standard Cat-5 cables, AES/EBU Standard cables

Page 52

A C T I V E S T U D I O M O N I T O R S

Cables

Below is a guide to the cables used in iDP™ set-up’s.

TC LINK Standard Cat-5 cables

Maximum Cable Length : 15 metres.

Cable type : Shielded Ethernet Cable Category 5.

Connector type : RJ45

This connection carries Digital audio (24 bit) and network control information.

P1 (pin No.)

P2(pin No.) Colour

1 1 Brown

2 2 White/Brown

3 3 Green

4 4 White/Blue

5 5 Blue

6 6 White/Green

7 7 Orange

8 8 White/Orange

	AES/EBU Standard cables	Pin1	Pin1	Ground
		Pin1	Pin1	Ground
	Maximum Cable Length: 100 m	Pin2	Pin2	Hot (+)
	Maximum Cable Length: 100 m	Pin3	Pin3	Cold (-)
	Cable type: 110 Ohm	Pin3	Pin3	Cold (-)
	Cable type: 110 Ohm
	Connector type: XLR

Serial to Cat-5 cable

This cable is included with the iDP SOFT™ and PC-iP™.

This is a proprietary cable with integral

Electronics. For use with iDP™ Systems only.

USB to COM 9pin

This cable isNOT included with iDP SOFT™ or PC-iP™. Use this type of converter along with the Cat5 to Serial cable described above if your computer has a USB connection only and no serial port.

52

Image 52

Contents Owners M a N U a L Page Important Safety Instructions Important Safety Instructions Quick Setup Guide T I V E S T U D I O M O N I T O R S Introduction Concept & Design Philosophy Tannoy Dual ConcentricUnpacking & Visual Checks High efficiency compact Switched Mode Power Supply SmpsTannoy WideBand SuperTweeter Preliminary Recommendation Speaker PlacementOrientation Master & Slave Concept Remote Control Slave Monitor & SubwooferInitializing the Network IDP Soft Software RemoteMaster Unit Slave/SubwooferSUB General Setup Procedure IDP Display MasterGeneral Setup Procedure SetupsAnalog Stereo Set-up With Mono Subs Analog Stereo Set-up With Stereo Subs Stereo Digital Set-up With Mono SubsAnalog Set-up Digital Set-upDigital 192kHz Set-up Digital Set-up Analog Set-up Alternative 7.1 Set-up Analog, Digital& 192kHzConnecting Two Subs Connecting Three SubsDig/6 Master Stereo Set-up With Chains on L&R. Analog or DigitalSetup when the monitors are connected Reset Procedure Reset All SettingsSelect Setup Select Monitor TasksPress Enter to access the Select Mode Parameter DescriptionMain Display † PC-iPPhase Bass ManagementLFE Low Pass Filter LFE GainSetup Menu SetupSet Monitor Task External ClockParameters available for the subwoofer LFE channel importantParameter Categories IDP Remote Preset 1/3 and 2/4 keys Volume potentiometerREF Level keys MUTE/UNMUTE Solo keys for the channels R LS- SUB RSInstallation on PC Installation on MacIDP Soft Minimum requirementsVolume Control REF LEV. keysMonitor and Sub icons Bass Mgt Bass ManagementIDP Soft Preset List Recall presetsStore presets Locked symbol in Preset ListIDP Soft Network Upload Software to MonitorsAnalog Gain System Setup ConfigurationBNC Sync Monitor Assignment Calibrate Main MonitorsCalibrate Subwoofer LFE Gain Range 0 to 14dB Phase RangeLFE Low Pass Filter Chained monitors Technical Specifications Precision 6 iDP System Master & SlavesTechnical Specifications- Precision 8 iDP Technical Specifications TS212 iDP Subwoofer TS112 iDP Subwoofer & iDPDimensions Precision 6 iDP Dimensions Precision 8 iDP Dimensions Precision TS212 iDP Grey/Silver Dimensions Precision TS112 iDP GreyIDP Display Messages System Delays Sample Rate Digital Input Analog Input Curves ExplainedSUB LFE Cables TC Link Standard Cat-5 cablesAES/EBU Standard cables Serial to Cat-5 cableDeclaration Of Conformity Warranty Page Issue Software Version 1.53 Part No GH 01 December