Tannoy ACTIVE STUDIO MONITORS owner manual Analog Stereo Set-up With Stereo Subs

Page 17

Analog Stereo Set-up With Stereo Subs

The diagram shows how to connect a stereo set-up with two subwoofers.

The Left monitor is set as the System Controller by leaving out the TC Link button on the rear panel.

The Left master monitor receives both the left and right input signals via the analog input connectors.

The Right monitor and Sub receive audio and control via the output RJ45 TC Link connections on the Left (system controller) monitor.

When no Bass management is selected, no signal will be sent to the subwoofers.

When Bass management is selected, low frequency content from the left channel is extracted and sent to the left subwoofer. Low frequency content from the right channel is extracted and sent to the right subwoofer.

The iDP™ Remote, iDP SOFT™ or PC-iP™can be connected to any spare TC Link “out” connection.

! REMEMBER – To set a master monitor as the system controller the TC Link button on the rear panel MUST be in the out position.

Stereo Digital Set-up With Mono Sub(s)

The diagram shows how to connect a digital stereo set-up with

one subwoofer. If you are using a standard stereo set up (no subwoofer) then simply omit the subwoofer.

The Left monitor is set as the System Controller by leaving out the TC Link button on the rear panel.

The Left monitor receives both the left and right input signals via the AES input.

The right monitor and Sub receive audio and control via the output RJ45 TC Link connections on the Left (system controller) monitor.

When no Bass management is selected, no signal will be sent to the subwoofer.

When Bass management is selected, low frequency content from the left and right channels is extracted and sent to the subwoofer.

The iDP™ Remote, iDP SOFT™ or PC-iP™can be connected to any spare TC Link “out” connection.

If using stereo subs connect in the same way as 2.2 analog.

! REMEMBER – To set a master monitor as the system controller the TC Link button on the rear panel MUST be in the out position.

17

Image 17

Contents Owners M a N U a L Page Important Safety Instructions Important Safety Instructions Quick Setup Guide T I V E S T U D I O M O N I T O R S Introduction Tannoy Dual Concentric Concept & Design PhilosophyTannoy WideBand SuperTweeter High efficiency compact Switched Mode Power Supply SmpsUnpacking & Visual Checks Orientation Speaker PlacementPreliminary Recommendation Master & Slave Concept Slave Monitor & Subwoofer Remote ControlInitializing the Network IDP Soft Software RemoteSlave/Subwoofer Master UnitSUB IDP Display Master General Setup ProcedureAnalog Stereo Set-up With Mono Subs SetupsGeneral Setup Procedure Stereo Digital Set-up With Mono Subs Analog Stereo Set-up With Stereo SubsDigital Set-up Analog Set-upDigital 192kHz Set-up Digital Set-up Analog Set-up Analog, Digital& 192kHz Alternative 7.1 Set-upConnecting Three Subs Connecting Two SubsStereo Set-up With Chains on L&R. Analog or Digital Dig/6 MasterSetup when the monitors are connected Reset All Settings Reset ProcedureSelect Setup Select Monitor TasksParameter Description Press Enter to access the Select ModeMain Display † PC-iPBass Management PhaseLFE Low Pass Filter LFE GainSetup Setup MenuSet Monitor Task External ClockLFE channel important Parameters available for the subwooferParameter Categories IDP Remote Volume potentiometer Preset 1/3 and 2/4 keysREF Level keys MUTE/UNMUTE Solo keys for the channels R LS- SUB RSInstallation on Mac Installation on PCIDP Soft Minimum requirementsREF LEV. keys Volume ControlMonitor and Sub icons Bass Mgt Bass ManagementRecall presets IDP Soft Preset ListStore presets Locked symbol in Preset ListUpload Software to Monitors IDP Soft NetworkBNC Sync System Setup ConfigurationAnalog Gain Calibrate Main Monitors Monitor AssignmentCalibrate Subwoofer LFE Low Pass Filter Phase RangeLFE Gain Range 0 to 14dB Chained monitors System Master & Slaves Technical Specifications Precision 6 iDPTechnical Specifications- Precision 8 iDP TS112 iDP Subwoofer & iDP Technical Specifications TS212 iDP SubwooferDimensions Precision 6 iDP Dimensions Precision 8 iDP Dimensions Precision TS112 iDP Grey Dimensions Precision TS212 iDP Grey/SilverIDP Display Messages Curves Explained System Delays Sample Rate Digital Input Analog InputSUB LFE TC Link Standard Cat-5 cables CablesAES/EBU Standard cables Serial to Cat-5 cableDeclaration Of Conformity Warranty Page Issue Software Version 1.53 Part No GH 01 December