Tannoy ACTIVE STUDIO MONITORS owner manual Parameter Categories

Page 31

Parameter Categories

Global Parameters

These parameters apply to the entire system: -

Global parameters stored with presets

•Bass Management

•Mute Status

Global parameters NOT stored with presets

•Ref. Levels

•Analog Input Sensitivity

•Selected Setup

•BNC Sync

Local Parameters

These parameters apply to individual Precision monitors: -

Local parameters stored with presets

•X-Curve

•Parametric EQ setting (set via optional PC-iP™)

•LFE Gain (subs)

•LFE Low Pass (subs)

•Rel. Level

Local parameters NOT stored with presets

•Bass and Treble

•Delay

•Lock status (set via optional PC-iP™)

•Room position

•Calibration Level

•Tasks

•Phase (Subs)

•Polarity (Subs)

Recall

•Press ENTER and use ARROW keys to select presets

•Press ENTER to recall/load the selected preset

If no user-preset are stored on locations 1 to 4, presets 16 to 19 are loaded instead.

Complete preset list is available on page 52.

Store

•Press ENTER and select storage location using the ARROW keys

•Press ENTER again to store.

Storage location can be 1-15.

Parameter can be locked via the optional PC-iP™Installers software. When trying to change values on a locked parameter the LCD display reads “Locked”.

31

Image 31

Contents Owners M a N U a L Page Important Safety Instructions Important Safety Instructions Quick Setup Guide T I V E S T U D I O M O N I T O R S Introduction Tannoy Dual Concentric Concept & Design PhilosophyUnpacking & Visual Checks High efficiency compact Switched Mode Power Supply SmpsTannoy WideBand SuperTweeter Preliminary Recommendation Speaker PlacementOrientation Master & Slave Concept IDP Soft Software Remote Remote ControlSlave Monitor & Subwoofer Initializing the NetworkSlave/Subwoofer Master UnitSUB IDP Display Master General Setup ProcedureGeneral Setup Procedure SetupsAnalog Stereo Set-up With Mono Subs Stereo Digital Set-up With Mono Subs Analog Stereo Set-up With Stereo SubsDigital Set-up Analog Set-upDigital 192kHz Set-up Digital Set-up Analog Set-up Analog, Digital& 192kHz Alternative 7.1 Set-upConnecting Three Subs Connecting Two SubsStereo Set-up With Chains on L&R. Analog or Digital Dig/6 MasterSetup when the monitors are connected Select Monitor Tasks Reset ProcedureReset All Settings Select Setup† PC-iP Press Enter to access the Select ModeParameter Description Main DisplayLFE Gain PhaseBass Management LFE Low Pass FilterExternal Clock Setup MenuSetup Set Monitor TaskLFE channel important Parameters available for the subwooferParameter Categories IDP Remote MUTE/UNMUTE Solo keys for the channels R LS- SUB RS Preset 1/3 and 2/4 keysVolume potentiometer REF Level keysMinimum requirements Installation on PCInstallation on Mac IDP SoftBass Mgt Bass Management Volume ControlREF LEV. keys Monitor and Sub iconsLocked symbol in Preset List IDP Soft Preset ListRecall presets Store presetsUpload Software to Monitors IDP Soft NetworkAnalog Gain System Setup ConfigurationBNC Sync Calibrate Main Monitors Monitor AssignmentCalibrate Subwoofer LFE Gain Range 0 to 14dB Phase RangeLFE Low Pass Filter Chained monitors System Master & Slaves Technical Specifications Precision 6 iDPTechnical Specifications- Precision 8 iDP TS112 iDP Subwoofer & iDP Technical Specifications TS212 iDP SubwooferDimensions Precision 6 iDP Dimensions Precision 8 iDP Dimensions Precision TS112 iDP Grey Dimensions Precision TS212 iDP Grey/SilverIDP Display Messages Curves Explained System Delays Sample Rate Digital Input Analog InputSUB LFE Serial to Cat-5 cable CablesTC Link Standard Cat-5 cables AES/EBU Standard cablesDeclaration Of Conformity Warranty Page Issue Software Version 1.53 Part No GH 01 December