Rockford Fosgate FFX6 manual Installation, Remote Punch Bass, Mounting Clip Knob Decal

Page 7

INSTALLATION

7.Securely mount the amplifier to the vehicle or amp rack. Be careful not to mount the amplifier on cardboard or plastic panels. Doing so may enable the screws to pull out from the panel due to road vibration or sudden vehicle stops.

8.Connect the source signal to the amplifier by plugging the RCA cable inputs into the input jacks at the amplifier.

9.Connect the speakers. Strip the speaker wires 1/2" and insert into the speaker terminal and tighten the set screw to secure into place. Be sure to maintain proper speaker polarity. DO NOT chassis ground any of the speaker leads as unstable operation may result.

10.Perform a final check of the completed system wiring to ensure that all connections are accurate. Check all power and ground connections for frayed wires and loose connections which could cause problems.

NOTE: Follow the diagrams for proper signal polarity.

!CAUTION: These amplifiers are not recommended for impedance loads below 2.

REMOTE PUNCH BASS

Mounting and installation

1.Find a location, either under the dash or near the center console, that gives easy access to the remote.

2.Using the screws supplied, install the mounting clip with the tabs towards the back.

3.Route the cable for the remote and connect to both the remote and amplifier.

4.Slip the remote onto the mounting clip until it snaps into place.

5.Install the decal and knob onto the remote.

Mounting

Clip

Knob

Decal

7

Image 7
Contents FFX6 Introduction Table of ContentsContents of Carton Safety InstructionsPower Connection Top Amplifier Design FeaturesTrunk preferred and Passenger Compartment Mounting Installation Installation ConsiderationsMounting Locations Engine CompartmentBattery and Charging Installation Mounting AmplifierWiring the System Mounting Clip Knob Decal InstallationMounting and installation Remote Punch BassColor Options Operation Adjusting GainAdjusting Crossover Frequency Infrasonic FilterFFX6 Applications Recommended Configuration for ONE 1 AmplifierFFX6 Applications Recommended Configuration for TWO 2 AmplifiersProcedure 3 Check Amplifier for audio output TroubleshootingProcedure 1 Check Amplifier for proper connections Procedure 2 Check Amplifier Protection circuitMODEL- Class bd SpecificationsLimited Warranty Information Length of WarrantyTable DES Matières FrançaisContenu DE Lemballage Consignes DE SécuritéConnexion dalimentation Particularités TechniquesDessus de Lampli Emplacements DE Montage Installation Considérations Concernant L’INSTALLATIONMontage dans le coffre de préférence et lhabitacle passager Montage DE LampliBatterie ET Charge Câblage DU SystèmeMontage et installation Basses Punch À TélécommandeBouton Choix DE Couleur Fonctionnement Réglage DU GainRéglage DE LA Fréquence DU Filtre Filtre InfrasoniqueModèle Applications Configuration Recommandée Pour UN 1 AmpliFFX6 Procédure 3 vérifiez la sortie audio de l’ampli AccessoiresDépannage Procédure 2 Vérifiez le circuit de protection de lampliModèle Class bd CaractéristiquesGarantie Limitée Durée de la garantieÍndice DE Materias IntroducciónInstrucciones DE Seguridad InicioConexión de corriente Parte superior del Amplificador Características DEL DiseñoLugares DE Montaje Instalación Consideraciones Sobre LA InstalaciónCompartimento del motor Cableado DEL Sistema InstalaciónMontaje DEL Amplificador Batería Y CargaBroche de montaje Perilla Calcomanía Bajo Punch Remoto Punch BassMontaje e instalación Opciones DE Colores Operación Ajuste DE LA GananciaAjuste DE LA Frecuencia DE X-OVER Transición Filtro InfrasónicoModelo 2FFX6 Accessorios Solución DE ProblemasCapacitores conectores Punch Especificaciones Información Sobre LA Garantía Limitada Amplificadores POWER-2 añosAmplificadores Type RF-3 añosInhaltsverzeichnis EinleitungAm Gerät, Feuer bzw. mögliche Verletzungen zu vermeiden SicherheitshinweiseStromanschluss Oberseite des Verstärkers DesigncharakteristikenBefestigungsstellen Einbau EinbauüberlegungenMotorraum Verkabelung DES Systems EinbauBefestigung DES Verstärkers Batterie UND AufladungBefestigungs- klemme Regler Aufkleber Punch Bass FernbedienungFarboptionen Betrieb Lautstärke Gain EinstellenCROSSOVER-FREQUENZ Einstellen InfraschallfilterAnwendungen FÜR Einen 1 Verstärker Empfohlene Konfiguration ModellAnwendungen FÜR Zwei 2 Verstärker Empfohlene Konfiguration Zubehör FehlerbeseitigungOder OrerDie technischen Daten können sich ohne Ankündigung ändern Technische DatenInformationen ZUR Beschränkten Garantie Laufzeit der GarantieIndice IntroduzioneContenuto DELL’IMBALLAGGIO Istruzioni DI SicurezzaCollegamento alla tensione Caratteristiche DEL DesignSommità Dell’amplificatore Posizionamento Installazione Considerazioni SULL’INSTALLAZIONEScompartimento del motore Cablaggio DEL Sistema InstallazioneFissaggio DELL’AMPLIFICATORE Batteria E CaricamentoManopola Decalcomania Montaggio ed installazioneOpzioni PER IL Colore Funzionamento Regolazione DI GuadagnoRegolazione Della Frequenza DI Incrocio Filtro InfrasonicoModello FFX6 Italiano Condensatori della Connecting Punch AccessoriINDIVIDUAZIONE/RIPARAZIONE Guasti Modello Class bd SpecificheInformazioni Inerenti Alla Garanzia Limitata Lunghezza della garanziaNota Nota Rockford Fosgate