Toshiba B-SX5T-TS25-QM-R, BSX5TTS25QMR manual Printer Setup, Setup Flow, Procedure, Reference

Page 15

2. PRINTER SETUP

ENGLISH VERSION EO1-33059

2. PRINTER SETUP

2. PRINTER SETUP

This section outlines the procedures to setup your printer prior to its operation. The section includes precautions, loading media and ribbon, connecting cables, setting the operating environment of the printer, and performing an online print test.

Setup Flow

Installation

Fitting the fan filter

Connecting the power cord

Loading the media

Media sensor position

alignment

Loading the ribbon

Connecting to a host computer

Turning the power ON

Setting the operating

environment

Installing the printer driver

Print test

Position and Print Tone Fine

adjustment

Automatic threshold setting

Manual threshold setting

Procedure

After referring to the Safety Precautions in this manual, install the printer on a safe and stable location.

Fit the supplied fan filter to the ventilation of the printer.

Connect a power cord to the power inlet of the printer, then, to an AC outlet.

Load a label stock or tag stock.

Adjust the position of feed gap sensor or black mark sensor according to the media to be used.

In case of thermal transfer printing, load the ribbon.

Connect the printer to a host computer or a network.

Turn on the printer power.

Set the printer parameters in the system mode.

If necessary, install the printer driver in your host computer.

Make a print test in your operating environment and check the print result.

If necessary, fine adjust the print start position, cut/strip position, print tone, etc.

If the print start position cannot be detected properly when pre-printed label is used, set the threshold automatically.

If the print start position cannot be detected properly even an automatic threshold setting is performing, manually set the threshold.

Reference

2.1Installation

2.2Fitting the Fan Filter

2.3Connecting the Power Cord

2.4Loading the Media

2.4Loading the Media

2.5Loading the Ribbon

2.6Connecting the Cables to Your Printer

2.7Turning the Printer

ON/OFF

2.9Setting an Operating Environment

2.10Installing the Printer Drivers

2.11Print Test

2.12Position and Print Tone Fine Adjustment

2.13Threshold Setting

2.13Threshold Setting

E2- 1

Image 15

Contents SX5T Series Vorsicht CE Compliance for EU onlySX5T Series Waste Recycling information for users For all countries and areas Meanings of Each Symbol Safety SummaryRequest Regarding Maintenance PrecautionsTable of Contents EA1-1 E5-1E6-1 E7-1Product Overview Introduction Features UnpackingContents AccessoriesDimensions Front ViewRear View Interior Operation PanelOption Name Type Usage OptionsReference Printer SetupSetup Flow ProcedureInstallation Connecting the Power Cord Fitting the Fan FilterExample of US Type Loading the Media Do not over-tighten the Locking Ring of the Supply Holder Setting the Feed Gap Sensor position Batch mode Strip modeSTANDARD/PEEL OFF position Adjustment Built-in rewinder modeCut mode Option Loading the Ribbon Auto Ribbon Saving Mode Connecting the Cables to Your Printer Turning on the Printer Turning the PrinterPcmcia Cards How to enter the System Mode Sequentially Parameter SettingCharacter Zero Selection Character Code SelectionData Length Selection Baud Rate SelectionStop Bit Selection Parity SelectionFlow Control Code Selection Auto Forward Wait Selection LCD Language SelectionFeed key Head Up Cut/Rewinder SelectionRibbon Saving Function Selection Solenoid Type SelectionControl Code Selection Feed Key Function Selection Strip Wait Status SelectionEuro Code Selection Kanji Code SelectionCentronics Interface ACK/BUSY Timing Selection Auto Print Head Check SelectionInput Prime Selection Web Printer Function SelectionExpansion I/O Interface Type Selection Ribbon Near End SelectionPlug & Play Selection Centronics Interface SelectionPre-Strip Selection Label End/Ribbon End SelectionReverse Feed Speed Selection Maxi Code Specification SelectionPrint Head Type Selection Dumped Dump Mode SettingRequired Label Length Receive Buffer SizeWhen the Pause key is pressed, Basic program is executed Installing the Printer Drivers IntroductionGeneral Description Parallel Interface Installing the Printer DriverWindows 98/Me E2-39 Windows 2000/XP E2-41 USB Interface E2-43 E2-44 E2-45 Finish button E2-47 E2-48 E2-49 Uninstalling the Printer Driver Adding a LAN Port Windows 98/ME Adding/Deleting a LAN PortDeleting a LAN Port Others Printer Driver UpgradesUsing the Printer Driver Print Test AdjustmentWhen using a Strip Module or an optional Cutter Module Coordinate Fine Adjustment Position and Print Tone Fine AdjustmentFeed Amount Fine Adjustment Cut/Strip Position Fine AdjustmentTone Fine Position and PrintExample of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Restart Feed When setting -50.0 mm Position and Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Threshold Setting Feed and Pause keys „ When using the Feed Gap Sensor „ When using the Black Mark Sensor„ Storing a No Media Level Voltage „ Manual Threshold SettingTHRESHOLDR4.0V THRESHOLDT4.0V THRESHOLDR3.9V Operation Panel On Line ModeOperation ResetMaintenance CleaningPrint Head/Platen/ Sensors Covers and Panels Optional Cutter Module Restart key TroubleshootingError Messages Error Messages Problems/Causes SolutionsError Messages Problems/Cause Solutions Possible Problems Causes Solutions Possible ProblemsRefer to .1 Media Removing Jammed Media Model Printer SpecificationsSX5T-TS22-QM-R Label Supply SpecificationsMedia Media TypeDetection Area of the Transmissive Sensor LabelTag paper with square holes Effective Print Area Detection Area of the Reflective SensorRfid Tags „ B-9704-RFID-U1-US-R and B-9704-RFID-U1-EU-R„ B-9704-RFID-H1-QM-R Media feed direction Ribbon Recommended Media and Ribbon TypesMedia type Description Care/Handling of Media and Ribbon Ribbon type DescriptionCombination of Media and Ribbon Appendix 1 Messages and Leds Symbols in the messageSystem Error Following message appears Parallel interface Centronics Standard Appendix 2 InterfaceConnector Serial interface Standard LAN Option B-9700-LAN-QM-R Expansion I/O Interface Option B-7704-IO- QM-R RFID-U1-US RFID-U1-EURFID-H1-QM When purchasing the power cord Appendix 3 Power CordAppendix 4 Print Samples EAN13+5 digits Interleaved 2JAN13, EAN13 EAN13+2 digitsKIX Code UPC-A+5 digitsIndustrial 2 Customer bar codeBar code Appendix 5 GlossariesUSB Universal Serial Bus Print head elementIndex Power LEDIndex EO1-33059

Related manuals

Manual 56 pages 47.42 Kb